background image

GB - 5

• Do not operate the unit unless all controls 

function as described in this manual.

Before attempting to operate your 
unit:

1. Make sure all assembly has been 

properly completed.

2. Understand all Safety Precautions 

provided in the manuals.

3. Review control functions and operation of 

the unit.

4. Review recommended lubrications, 

maintenance and adjustments.

5. Review Limited Warranty Policy.
6. Fill out Original Purchaser Registration 

Card and return the card to Ariens 
Company.

DISCLAIMER 

Ariens reserves the right to discontinue, 
change, and improve its products at any time 
without notice or obligation to the purchaser. 

The descriptions and specifications contained 
in this manual were in effect at printing. 
Equipment described within this manual may 
be optional. Some illustrations may not be 
applicable to your unit.

SAFETY ALERTS

Look for these symbols to point 
out important safety precautions. 
They mean:

Attention!

Personal Safety Is Involved!

Become Alert! 

Obey The Message!

The safety alert symbols above and signal 
words below are used on decals and in this 
manual.

Read and understand all safety messages.

NOTATIONS

NOTE: 

 General reference information for 

proper operation and maintenance practices.

IMPORTANT: 

Specific procedures or 

information required to prevent damage to unit 
or attachment.

PRACTICES AND LAWS

Practice usual and customary safe working 
precautions, for the benefit of yourself and 
others. Understand and follow all safety 
messages. Be alert to unsafe conditions and 
the possibility of minor, moderate, or serious 
injury or death. Learn applicable rules and 
laws in your area.

REQUIRED OPERATOR TRAINING

If unit is to be used by someone other than 
original purchaser; loaned, rented or sold, 
ALWAYS provide this manual and any needed 
safety training before operation.

SAFETY DECALS AND 
LOCATIONS

ALWAYS replace missing or damaged Safety 
Decals. Refer to figure below for Safety Decal 
locations.

WARNING: 

Improper assembly or 

adjustments can cause serious 
injury. 

SAFETY

DANGER: 

IMMINENTLY 

HAZARDOUS SITUATION! If 
not avoided, WILL RESULT in 
death or serious injury. 

WARNING: 

POTENTIALLY 

HAZARDOUS SITUATION! If not 
avoided, COULD RESULT in death 
or serious injury. 

CAUTION: 

POTENTIALLY 

HAZARDOUS SITUATION! If not 
avoided, MAY RESULT in minor or 
moderate injury. It may also be 
used to alert against unsafe 
practices. 

Summary of Contents for 946150 - ST622 CARB





















Reviews: