manualshive.com logo in svg

Ariens 920025, Service Manual, Page: 16 / 60

Share
Download
Ariens 920025 Service Manual Download Page 16

EN – 12

ATTACHMENT DRIVE BELT 
REPLACEMENT

Remove Attachment Drive Belt

IMPORTANT: 

Save all hardware for reinstallation.

1.

Stop engine, remove key and wait for all moving parts 
to stop and for hot parts to cool.

2.

Disconnect spark plug wire from engine.

3.

Remove auger housing. See 

Separate Housing from 

Frame

 on page 7.

4.

Remove attachment drive belt from attachment drive 
pulley. See Figure 16.

Install Attachment Drive Belt

1.

Install belt onto attachment drive pulley.

2.

Reinstall auger housing to frame. See 

Reinstall Auger 

Housing

 on page 9.

3.

Adjust attachment clutch / brake. Refer to Operator’s 
Manual for adjustment procedure.

4.

Reconnect spark plug wire.

IMPORTANT: 

Check all adjustments after first use.

TRACTION DRIVE BELT 
REPLACEMENT

Remove Traction Drive Belt

IMPORTANT: 

Save all hardware for reinstallation.

1.

Stop engine, remove key and wait for all moving parts 
to stop and for hot parts to cool.

2.

Disconnect spark plug wire from engine.

3.

Loosen traction drive clutch cable. See Figure 17.

4.

Remove auger housing. See 

Separate Housing from 

Frame

 on page 7.

WARNING: 

AVOID INJURY. Auger / impeller 

must stop within 5 seconds when attachment 
clutch lever is released.

Figure 16

Figure 17

Summary of Contents for 920025





























































Reviews:

No comments