manualshive.com logo in svg

Ariens 915013-1742 EZR, Owner'S/Operator'S Manual, Page: 26 / 34

Share
Download
Ariens 915013-1742 EZR Owner'S/Operator'S Manual Download Page 26

GB - 26

5. Install new belt onto clutch sheave, then engine 

sheave. Check for belt alignment and clearance.

6. Connect clutch shaft idler spring to bolt.

7. Reinstall transaxle belt.

ADJUSTMENTS

Neutral Adjustment (Speed Control Lever)

NOTE: 

915013 with Serial Numbers Less Than 10,500. 

Other Units with Serial Numbers Less Than 1,000.

1. Stop the engine. Remove the ignition key. Push 

the PTO knob into the “OFF” position.

2. Place jack(s) under rear transaxles only. If jack(s) 

are not available, place support blocks under both 
transaxles at the rear of the unit.

3. Raise the rear drive wheels off the floor. Remove 

side shrouds. Set aside.

4. Start the engine and run it at part throttle.

5. Loosen the two lock nuts holding the Speed 

Control Arm.

6. Rotate Flange Bushing until the wheel stops 

rotating.

7. Lock the Speed Control Arm in place by 

tightening the two lock nuts.

8. Repeat procedure for other side of unit.

9. Reinstall side shrouds.

Neutral Adjustment (Speed Control Lever)

NOTE: 

All Other Units

1. Stop the engine. Remove the ignition key. Push 

the PTO knob into the “OFF” position.

2. Lock steering levers in neutral. (See 

Neutral Lock

 

in 

Operation

.)

3. Place jack(s) under rear transaxles only. If jack(s) 

are not available, place support blocks under both 
transaxles at the rear of the unit.

4. Raise the rear drive wheels off the floor. Remove 

side shrouds. Set aside.

5. Loosen nuts on transaxle linkage.

6. Start the engine and run it at part throttle.

Transaxle should set neutral automatically 
(wheels do not spin).

NOTE: 

If transaxle does not set neutral, contact your 

Ariens Dealer for repair.

7. Shut off engine.

8. Tighten nuts on transaxle linkage without moving 

the pivot arm or transaxle rod.

9. Repeat procedure for other side of unit.

CAUTION: 

PREVENT personal injury! 

ALWAYS MAKE CERTAIN that jack(s) or 
blocks used are stable, strong and will 
support the weight of the unit.

OE0841

2

1

3

4

5

6

1. Transaxle Belt
2. Clutch Shaft Idler 

Spring

3. Clutch Shaft Belt

4. Engine Sheave
5. Clutch Sheave
6. Clutch Idler

CAUTION: 

PREVENT personal injury! 

ALWAYS MAKE CERTAIN that jack(s) or 
blocks used are stable, strong and will 
support the weight of the unit.

Speed Control Arm

Locknuts and Bolts

Locknuts and Bolts

Flange Bushing

OE0082

Eccentric

Summary of Contents for 915013-1742 EZR



































Reviews:

No comments