Argus 152 Manual Download Page 44

Page: 44 / 408

7 Operation on xDSL accesses

ARGUS 152

Establishing the xDSL connection using VDSL as an example

Profile configuration:

ARGUS uses the settings (see page 28) and limit values (see page 37) stored in the
respective profile for establishing a VDSL connection.

ARGUS in status screen.







ARGUS uses the default profile (profile 1
in the example) to establish the VDSL
connection.

Establishing a VDSL connection

ARGUS synchronises with DSLAM (LED
"Sync/L1" flashes, display shows element
on yellow background).



ARGUS displays the current connection
status (in this example "Initialize") in the
layer-1 box (blue).






While connecting:



Display:



<Edit>

Edits the VDSL settings and
MAC address.

<Access>

Selects a new access.

Current connection status

Time elapsed since start of
synchronisation in h:min:s.

Continued on next
page

Summary of Contents for 152

























































































































































































































































































































































































































Search results

Summary of Contents for 152

Reviews:

Related manuals for 152

Brands by name

Popular brands

Argus 152, Manual

Search results

Summary of Contents for 152

Reviews:

Related manuals for 152

Brands by name

Popular brands