manualshive.com logo in svg

Argus 152, Manual

The Kenmore 152 is a versatile and reliable appliance that simplifies your daily chores. To gain full control and maximize its potential, make sure to download the comprehensive Owner's Manual from manualshive.com for free. This handy manual is your go-to resource, offering detailed instructions and tips for optimal product usage.

Share
Download
background image

7 Operation on xDSL accesses

37

ARGUS 152

 

7.2 xDSL settings

ARGUS stores all relevant settings (e.g. set and limit values) for a test with the accesses. 
Only the relevant settings are applied, depending on the test situation. You can restore the 
default settings at any time (see page 363): 

Setting

Description

Phys. parameters:
ADSL:
Rated / 
treshold 
value

Setting 

Bitrate

Entry of the comparison value for the upstream and 
downstream ATM bitrate [kbit/s] using the number keys. 

ARGUS displays a large green "OK" in the ARGUS status 
screen if the current bitrate is above the set value for an 
active DSL connection and an "OK" for connection 
parameters below the target, otherwise "NOK". 

Default: 

d: 0 

and

 u: 0

CRC limit 
value

Sets the max. CRC (cyclic redundancy check) value.  

ARGUS displays a large green "OK" in the ARGUS status 
screen if the current value is below the set limit value for 
an active DSL connection and an "OK" for connection 
parameters below the target, otherwise "NOK".

Range: 0 to 999,999,999

Default: 

far: * 

and

 near: * 

(*=off)

FEC limit value Determines the maximum FEC (forward error correction) 

value.  

ARGUS displays a large green "OK" in the ARGUS status 
screen if the current value is below the set limit value for 
an active DSL connection and an "OK" for connection 
parameters below the target, otherwise "NOK".

Range: 0 to 999,999,999

Default: 

far: * 

and

 near: * 

(*=off)

HEC limit value Determines the maximum HEC (header error correction) 

value. 

ARGUS displays a large green "OK" in the ARGUS status 
screen if the current value is below the set limit value for 
an active DSL connection and an "OK" for connection 
parameters below the target, otherwise "NOK".

Range: 0 to 999,999,999

Default: 

far: * 

and

 near: * 

(*=off)

Summary of Contents for 152

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for 152

D-Link Express Ethernetwork DI-704P Quick Install Manual preview
Express Ethernetwork DI-704P
Brand: D-Link Pages: 17
D-Link DI-106 Series Faq preview
DI-106 Series
Brand: D-Link Pages: 29
D-Link DGS-3700 Series User Manual preview
DGS-3700 Series
Brand: D-Link Pages: 292
D-Link DGS-3224SR User Manual preview
DGS-3224SR
Brand: D-Link Pages: 140
D-Link DGS-1224T - Web Smart Switch User Manual preview
DGS-1224T - Web Smart Switch
Brand: D-Link Pages: 61
D-Link DI-LB604 - Load Balancing Router Quick Installation Manual preview
DI-LB604 - Load Balancing Router
Brand: D-Link Pages: 14
D-Link DIR-605L Specification preview
DIR-605L
Brand: D-Link Pages: 2
D-Link DIR-510L Manual preview
DIR-510L
Brand: D-Link Pages: 45
D-Link DES-3550 Manual preview
DES-3550
Brand: D-Link Pages: 218
D-Link DES-3528 - xStack Switch - Stackable User Manual preview
DES-3528 - xStack Switch - Stackable
Brand: D-Link Pages: 322
D-Link DIR-130 - Broadband VPN Router How To Set Up preview
DIR-130 - Broadband VPN Router
Brand: D-Link Pages: 10
D-Link DIR-130 - Broadband VPN Router Troubleshooting Manual preview
DIR-130 - Broadband VPN Router
Brand: D-Link Pages: 4
D-Link DIR-130 - Broadband VPN Router Configuration preview
DIR-130 - Broadband VPN Router
Brand: D-Link Pages: 13
D-Link DIR Series Configuration Manual preview
DIR Series
Brand: D-Link Pages: 13
D-Link DI-804HV - Express ENwork Router Configuration Manual preview
DI-804HV - Express ENwork Router
Brand: D-Link Pages: 19
D-Link DI-808HV Quick Installation Manual preview
DI-808HV
Brand: D-Link Pages: 12
D-Link DI-804 Quick Install Manual preview
DI-804
Brand: D-Link Pages: 8
D-Link DI-604UP Quick Install Manual preview
DI-604UP
Brand: D-Link Pages: 16

Brands by name

Popular brands

Load more brands