Argus 152 Manual Download Page 383

Page: 383 / 408

Network See ISO 8208: 1987(E)



Table 5- Coding of the clearing cause field in clear indication packets, page 35

ARGUS

No answer from network (to a CALL-REQUEST or a CLEAR-REQUEST)

ARGUS

Unexpected or wrong answer from network (no CALL-CONNECTED or CLEAR-
INDICATION as answer to CALL-REQUEST)

ARGUS

The network has indicated in a DIAGNOSTIC message that the logical channel
is invalid.



Origin: No (=1) or a wrong LCN was set.

ARGUS

It was not possible to determine an internal or external cause.



Origin: Layer 2 could not be setup or remote end does not support X.31

ARGUS

The X.31 Layer 3 test was not performed. The error can only occur in a test log.

Network

See ISO 8208: 1987(E)



Figure 14a page 121



Figure 14b page 123 et seq.



And/or CCITT Recommendation X.25, Annex E

29 Appendix

ARGUS 152

383

X.31 Test – Error messages

X.31 Causes

0 to 255

257

258

259

512

65535

X.31 Diagnostic (only for a cause less than 256)

0 to 255

Summary of Contents for 152

























































































































































































































































































































































































































Search results

Summary of Contents for 152

Reviews:

Related manuals for 152

Brands by name

Popular brands

Argus 152, Manual

Search results

Summary of Contents for 152

Reviews:

Related manuals for 152

Brands by name

Popular brands