manualshive.com logo in svg

Argus 152, Manual

Share
Download
Argus 152 Manual Download Page 35

7 Operation on xDSL accesses

35

ARGUS 152

 

7 Operation on xDSL accesses

ARGUS supports the following DSL interfaces: ADSL, VDSL

ARGUS supports the following access modes on xDSL accesses: 

The individual DSL tests record and store data (e.g. traces of IP data). It is the 
user's responsibility to comply with the applicable legal requirements.

The line may not carry a DC voltage greater than 200 V DC and should be free of 
AC voltage components.

xTU-R

Terminal device mode (xDSL transceiver unit) see page 43.

ARGUS is connected to the xDSL access (in front of or behind the 
splitter). ARGUS replaces the modem and PC.

xTU-R bridge

Bridge mode (xDSL transceiver unit bridge) see page 66.

ARGUS is connected to the xDSL access and the PC. 

ARGUS replaces the xDSL modem.

xTU-R router

Router mode (xDSL transceiver unit router) see page 68.

ARGUS is connected to the xDSL access and the PC.

ARGUS replaces the xDSL modem and router.

Summary of Contents for 152

























































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands