Argos Malibu 553/4038 Assembly Instructions Manual Download Page 10

Page: 10 / 32

Finished

front edge

Finished

front edge

Finished

front edge

Step

Assembly Instructions

Prepare the left divider

Fit 3 CL runners

to the left divider .

The 1st screw uses

the 1st hole in from the

front of the runner.

The 2nd and 3rd screws

. use the holes that line

up with the other panel

holes.

Fit a screw into

the hole at the top of the

runner .

Fit a rail holder to the

left divider through

the top hole with screw

and into the mark hole

drilled in the left divider.

Make sure that it is fitted

straight, in line with the

panel edges and then fit

another screw using

the lower hole.

Insert 2 large locking

cam nuts into the left

divider .

Push 2 of the quickfit

dowels as far as they

will go into the left

divider .

Tap 6 wooden dowels

into the left divider .

Note:

Wooden dowels

must not

stick out from

the edge by more than

10mm or they may

damage other panels.

V a

1st

screw

Finished

front edge

Finished

front edge

Use the Main Fittings Bag for Steps 8 - end

V a

10mm

V a

https://www.youtube.com/watch?v=Z6lGMy19h7Q

Fixing Bottom Mounted Runners

Summary of Contents for Malibu 553/4038

































Search results

Summary of Contents for Malibu 553/4038

Reviews:

Brands by name

Popular brands

Argos Malibu 553/4038, Assembly Instructions Manual

Search results

Summary of Contents for Malibu 553/4038

Reviews:

Brands by name

Popular brands