Argos Malibu 3 Drawer 2 Door Robe Assembly Instructions Manual Download

Page: 3 / 20

Components -

Panels

Please check you have all the panels listed below

Glue Safety -

Take care when using glue, please follow the advice below

Skin contact:

Remove contami-

nation by washing with soap and

water. This procedure should be

followed prior to aeting and

drinking.

Eye contact:

Rinse immediately

with clean water for 15 minutes

and seek medical advice.

If swallowed:

Seek medical

advice immediately.

• Only clean using a damp cloth

and mild detergent, do no use

bleach or abrasive cleaners.

• This product should not be

discarded with household

waste. Take to your local

authority waste disposal centre.

• From time to time check that

there are no loose screws on

this unit.

Drawer Divider - D0034A

145 x 249mm

waterfall

80%

x 2

If you have damaged or missing components, call the

Customer Helpline: 03456 400800

quoting the reference

numbers below

Left Side

(D2871A)

(1808 x 496mm)

Base

(D2841A)

(716 x 476mm)

Top

(D2870A)

(716 x 494mm)

Right Side

(D2872A)

(1808 x 496mm)

Plinth

(D2873A)

(716 x 92mm)

x 2

Back Rail

(D2847A)

(716 x 92mm)

Rail

(D2874A)

(716 x 92mm)

Drawer Base

(T693-367)

(693 x 367mm)

x 3

Left Drawer Side

(W370-124LH)

(370 x 124mm)

x 3

Right Drawer Side

(W370-124RH)

(370 x 124mm)

x 3

Door

(D2857A)

(1198 x 353mm)

x 2

Drawer Back

(W682-124BCK)

(682 x 124mm)

x 3

Drawer Front

(D2783A)

(710 x 156mm)

x 3

Back

(X1710-740)

(1710 x 740mm)

Hanging Rail

(FHR704)

(704mm long)

Summary of Contents for Malibu 3 Drawer 2 Door Robe





















Search results

Summary of Contents for Malibu 3 Drawer 2 Door Robe

Reviews:

Related manuals for Malibu 3 Drawer 2 Door Robe

Brands by name

Popular brands

Argos Malibu 3 Drawer 2 Door Robe, Assembly Instructions Manual

Search results

Summary of Contents for Malibu 3 Drawer 2 Door Robe

Reviews:

Related manuals for Malibu 3 Drawer 2 Door Robe

Brands by name

Popular brands