manualshive.com logo in svg

Argos Malibu 2 Drawer 3 Door Robe 238/5792, Assembly Instructions Manual

Share
Download
Argos Malibu 2 Drawer 3 Door Robe 238/5792 Assembly Instructions Manual Download Page 12

Finished 

front edge

Assembly Instructions

11

Step

 

18

Step

 

19

Fit the left side 

Push the left side      

onto the assembly       

and secure it with 8 

screws     .

8

D

The measurement from top corner X to bottom corner X must be 

equal to the measurement from top corner Y to bottom corner Y

a:

Fit the back panels

a: 

Square up the unit by 

making sure that 

measurement 

x:x equals 

y:y.

Place the small back       

and the large back       

down onto the unit as 

shown.

Make sure that the 

backs are pushed 

up tight against 

each other and that 

they meet over the 

back edge of the 

upright.

b: 

Nail      around the 

outside edges of the 

backs.

Note:

 Do not nail where 

the backs meet. Nails 

should be spaced about 

150mm apart.

18

19

H

D

D

D

D

D

D

D

D

8

y

x

y

y

y

x

b:

H

Note:

 Do not 

nail where the 

backs meet.

18

19

Summary of Contents for Malibu 2 Drawer 3 Door Robe 238/5792





















Reviews:

No comments

Brands by name

Popular brands

Load more brands