Argos Kensington 402/7216 Assembly Instructions Manual Download Page 20

Page: 20 / 28

Fit the plinths

Position the 3 plinths

around the outside of the

assembly, ensuring that

the bottom edge of the

plinths are flush with the

bottom edge of the

sides, as shown.

Secure the 2 side

plinths through

the left side

and right side

using screws .

Carefully

stand the unit

up for the next

step.

Profiled

top edge

Assembly Instructions

Step

Finished

top edge

Finished

top edge

Profiled

top edge

Prepare the front

plinth

Screw 2 metal dowels

into the front plinth .

Step

Fit the plinths together

Push the 2 side plinths

onto the front plinth .

Use a screwdriver to

tighten the large locking

nuts fitted to the side

plinths .

Warning:

The

unit is heavy.

Lift with care.

Step

Summary of Contents for Kensington 402/7216





























Search results

Summary of Contents for Kensington 402/7216

Reviews:

Related manuals for Kensington 402/7216

Brands by name

Popular brands

Argos Kensington 402/7216, Assembly Instructions Manual

Search results

Summary of Contents for Kensington 402/7216

Reviews:

Related manuals for Kensington 402/7216

Brands by name

Popular brands