background image

Note:

 

if required the next 

page can be cut out and used 
as reference throughout the 
assembly. Keep this page with 
these instructions for future 
reference.

1

Safety and Care Advice 

Important

 

– Please read these instructions fully before starting assembly

• Check you have all the 

components and tools listed on 

the following pages. 

• Remove all fi

 ttings from the 

plastic bags and separate them 

into their groups.

• Keep children and animals 

away from the work area, small 

parts could choke if swallowed.
• Make sure you have enough 

space to layout the parts before 

starting. 

• During assembly

 do not stand 

or put weight on the product, 

this could cause damage.

• 

Assemble the item as close 

to its 

 nal position (in the same 

room) as possible.

• 

Assemble on a soft level 

surface to avoid damaging the 

unit or your 

 oor.

 • 

To reduce 

the likelihood of 

damaging your 

product please 

ensure that your 

power drill is set on a low torque 

setting.

• Only clean using a damp cloth 

and mild detergent, do no use 

bleach or abrasive cleaners. 

• From time to ti

m

e check that 

there are no loose screws on 

this unit.

• 

This product should not be 

discarded with household waste. 

Ta

ke to your local authority 

waste disposal centre.

Care and maintenance

Skin contact: 

Remove 

contamination by washing with 

soap and water. This procedure 

should also be followed prior to 

eating and drinking.

Eye contact: 

Rinse immediately 

with clean water for 15 minutes 

and seek medical advice. 

If swallowed: 

Seek medical 

advice immediately. 

Glue safety

 -

 

Ta

ke care when using glue, p

lease follow the advice below

• 

Assemble all parts and bolts 

loosely during assembly

, only 

once the product is complete 

should you fully tighten the bolts

• Regularly che

c

k and ensure 

that all bolts and 

 ttings are 

tightend properly.

Handy Hints

• Do not use this item if any 

components are missing or 

damaged. 

• Parts of the assembly will be 

easier with 2 people.

• Argos Ltd. MK9 2 NW.

• This product is intended for

children in the age 6 or above.

• Maximum load

50 kgs (top of desk). 

• Assembly of this product must

be carried out by a competent

adult.

IMPORTANT: RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE

• During assembly

 children 

should be kept away from the 

product due to possible risk of 

injury. 

Summary of Contents for HOME New Pagnell 606/9447
















Reviews: