manualshive.com logo in svg

Argos Adult Malibu 532/8038, Assembly Instructions Manual

Share
Download
Argos Adult Malibu 532/8038 Assembly Instructions Manual Download Page 17

N

A

A

N

16

Step

 

25

Assembly Instructions

Step

 

26

B

B

A

N

Prepare the plinth

Insert 2 large locking  

cam nuts      into the 

plinth      .

Push 2 of the quickfit 

dowels      as far as they 

will go into the plinth      .

Tap 2 wooden dowels  

into the plinth      .

A

15

15

15

B

N

15

12

Fit the plinth

Push the plinth       onto 

the right side      .

Turn the large locking    

cam nut      fitted to the 

plinth       clockwise as 

far as it will go to secure 

the panels.

Important:

 Make sure 

there is no gap between

the fitted panels.

Step

 

27

15

12

B

15

Prepare the back rail

Insert 2 large locking  

cam nuts      into the 

back rail      .

Push 2 of the quickfit 

dowels      as far as they 

will go into the back rail      

.    .

Tap 2 wooden dowels  

into the back rail      .

A

20

20

20

B

N

B

B

N

A

Finished 

front edge

20

15

Summary of Contents for Adult Malibu 532/8038





























Reviews:

No comments

Brands by name

Popular brands

Load more brands