background image

QUICK-START GUIDE

Full manual available to download from: www.Ares-RC.com

Full manual available to download from: www.Ares-RC.com

Quick-Start Guide

Product specifications are subject to change without notice. 

Due to ongoing development, the actual product may vary from 

images shown. 

This product contains chemicals known to the State of California 

to cause cancer, birth defects and other reproductive harm.

This product is not a toy! (14+) Recommended for ages 14 and 

up. Adult supervision required for ages under 18 years old. 

Contains small parts, keep out of reach of children 3 years of 

age and younger.

To download the full Owner’s Manual & 

Technical Information Guide, please visit 

www.Ares-RC.com or scan the QR code with 

your smart phone.

Distributed in the 

UK by:

J Perkins Distribution Ltd, 

Lenham,  

Kent, UK  

ME17 2DL. 

www.jperkins.com

Distributed in Australia by:

Model Engines (Aust.) Pty. Ltd.,  

Unit 1, 158-168 Browns Road, 

Noble Park,  

Victoria,  

3174,  

Australia. 

www.modelengines.com.au

 

Ph (03) 8793 5555  

[email protected]

Distributed in the US by:

Firelands Customer Service/Product Support  

1133 Libra Drive, Lincoln, NE 68512 

www.firelandsgroup.com 

1-800-205-6773  

[email protected]

MADE IN CHINA

Part Number: 

AZSZ2802   Crossfire Racer Quad RFR: 200mW VTX

AZSZ2802A  Crossfire Racer Quad RFR: 25mW VTX

Summary of Contents for Crossfire AZSZ2802







Reviews: