background image

LL0291­W

LL0291­RGB

This  unit  should  only  be  used  for  purpose  for 
which  it  has  been  intended  and  should  be 
installed  using  the  instructions  which  are 
provided.  Arena  Luci  cannot  be  held  liable  for 
damages  to  person,  animals  or  objects  as  a 
result  of  improper,  unreasonable  and  wrong 
usage.
This  instruction  manual  contains  important 
information  about  the  installation  and  use  of  the 
projector.  Please  read  and  follow  these 
instructions carefully.
The  security  of  this  device  is  guaranteed  only 
with  the  proper  use  of  the  following  instructions, 
therefore they must be kept carefully.
Never  install  the  device  in  locations  easily 
accessible by people who ignore the existence of 
this user's manual and safety instructions.
For  the  wiring  please  refer  to  enclosed  wiring 
diagrams.  If  in  the  diagrams  indicated  there 
should not be that of your application, contact the 
technical office.
The  device  is  intended  exclusively  for  a 
submerged installation.
Disconnect the unit from any power supply before 
attempting  any  operation  in  contact  or  inside  the 
unit, and when not in use.
It  is  essential  that  electrical  installation  conforms 
to all relevant standards.
When  assembling  make  sure  that  the  cable 
glands are tightened for a watertight seal.
The device cannot be installed at a depth greater 
than 0.5 meters.
The  lamp  is  intended  only  for  underwater 

operation. Do not switch on the lamp outside the 
water for more than 10 seconds.
Never  install  the  device  in  areas  where  there  is 
no 

constant 

water 

flow; 

the 

maximum 

temperature must be below 40°C.
Prior  to  connect  the  unit  to  the  mains  supply, 
check  the  output  voltage  fits  the  technical 
requirements on the label.
Never  let  the  power  cord  come  into  contact  with 
other cables.
Never touch the electrical contacts, either directly 
with your fingers, or indirectly by means of sharp 
or metal objects.
Make sure that cables cannot cause trip hazard.
Do not attempt to dismantle and modify the unit.
Due  to  the  high  technological  level  of  this  unit, 
any service maintenance should be performed by 
specialised operators. Please contact your Arena 
Luci dealer for any operation.
Always ensure that the structure to which you are 
attaching the unit is secure and is able to support 
the weight of each unit.
LED module is not replaceable.
Do  not  use  any  solvent  based  cleaning  agents. 
Use only a soft, dry anti­static cloth.
The installation of LED modules (including power 
supplies)  should  be  done  according  to  current 
technical  rules  and  regulations.  The  installation 
should be performed only by a qualified operator.
Avoid  contact  with  either  corrosive  agents  or 
humidity  and  moisture  on  delicate  elements: 
damages  from  corrosion  are  not  refunded  as 
component defects.

WARNINGS

User's Manual

30W PAR 56 LED lamp for lighting pools and 

fountains

Please  note  that  as  part  of  Arena  Luci's  ongoing  commitment  to  continuous  product  development, 

specifications  are  subject  to  change  in  the  course  of  product  improvement  without  notice. Arena  Luci  is  not 

responsible for damages resulting from improper or different use than expected.

Summary of Contents for LL0291­-W

Page 1: ...ver install the device in areas where there is no constant water flow the maximum temperature must be below 40 C Prior to connect the unit to the mains supply check the output voltage fits the technical requirements on the label Never let the power cord come into contact with other cables Never touch the electrical contacts either directly with your fingers or indirectly by means of sharp or metal...

Page 2: ... shell Re tighten the M6x35 cap fixing screws respecting the original positions of the washers and the sealing springs POWER SUPPLY If you need more than one junction box to carry out the electrical distribution the connection of the LED head power cable to the power supply line must in any case be made in a junction box with adequate IP protection characteristics depending on the location of inst...

Page 3: ... from a distance and the synchronization of several lamps it is possible to use the optional control system with radio control code LC2041 The following table shows the automatic functions of color variation MAINTENANCE AND PERIODICAL CHECKS Mechanical parts Check that the projector is not mechanically damaged Clean the projector glass regularly using a soft cloth Carefully check the gaskets that ...

Page 4: ... in a quick and effective operation CE RULES The device meets the essential requirements of the Directives LVD 2014 35 UE EMC 2014 30 UE RAEE 2012 19 UE RoHS 2011 65 UE Ecodesign 2009 125 CE reg UE 1194 2012 Energy label 2010 30 UE reg UE 874 2012 reg UE 518 2014 GPSD 2001 95 CE Warnings Disposal of Old Electrical Electronic Equipment applicable in the European Union and other European countries w...

Reviews: