Arctic Cat MONSTER TRACTION P8814 Owner'S Manual Download Page 17

17

P8814pr-0920

IMPORTANT!

 Use this vehicle 

ONLY

 outdoors. Most interior flooring can be damaged by riding this vehicle indoors. Fisher-Price

®

 will 

not be responsible for damage to the floor if the vehicle is used indoors. As assembled, your vehicle is ready to roll in low speed 
(2

1

/

2

 mph, maximum). It has been pre-set so it will only operate in low speed. After your child has mastered the basic skills of driving 

and understands the rules for safe driving, it’s time to remove the high speed lock-out screw to allow the vehicle to operate in low or 
high speed.

 See the instructions in this section to remove the high speed lock-out screw.

Beginner Use - Low Speed

• Make sure the shifter is in the low speed 

 position 

1

.

• Press down on the foot pedal 

2

. The vehicle goes forward at 

a maximum of 2

1

/

2

 mph 

3

. Help your child practice steering to 

learn how far and how quickly to turn the steering wheel when 
driving forward in low speed.

To Back Up

Advanced Use - High Speed

• Before you disconnect the high speed lock-out, make sure your 

child knows how to steer, how to start and stop the vehicle and 
knows the rules for safe driving. When the high speed lock-out 
is disconnected, the vehicle can be driven forward in low speed 
(2

1

/

2

 mph, maximum) or high speed (5 mph, maximum).

• Make sure the shifter is in the low speed 

 position.

• Loosen and remove the screw in the shifter base.
• Place the lock-out screw into the hole in the shifter handle for 

future use. It can be re-inserted into the shifter base to lock-out 
high speed.

VEHICLE OPERATION

Remove 

lock-out screw 

for high speed.

• Your vehicle has a patented, electronic braking system that 

automatically stops the vehicle when your child’s foot lifts from 
the pedal. Make sure your child is comfortable with steering the 
vehicle and automatically knows how to stop.

STOP!

Store lock-out

screw here.

1

2

3

IMPORTANT!

 To avoid damaging the motors and gears, stop the 

vehicle before shifting from forward to reverse.
• Once your child is completely comfortable with operating the 

vehicle in the forward mode, introduce reverse 

.

• Make sure the shifter is in the reverse 

 position 

1

.

• Press down on the foot pedal 

2

.The vehicle will go in reverse 

at a maximum of 2

1

/

2

 mph 

3

. The vehicle is designed to 

operate in low speed only in reverse. Help your child practice 
steering to learn how far and how quickly to turn the steering 
wheel when driving in reverse.

1

2

3

To Drive

• Make sure the shifter is in the high speed  

  position 

1

.

• Press down on the foot pedal 

2

. The vehicle goes forward at 

a maximum of 5 mph 

3

. Help your child practice steering to 

learn how far and how quickly to turn the steering wheel when 
driving forward in high speed.

1

2

3

Summary of Contents for MONSTER TRACTION P8814


























Reviews: