ARCIMOTO FUV 2022 Owner'S Manual Download Page 83

Page: 83 / 194

WORKING WITH PINS

Working With PINs

Each FUV is assigned a unique 6- digit PIN (Personal

Identification Number) at the factory. This PIN can be

used to turn the FUV on and off without using a key.

The Factory-Assigned PIN for your FUV is:

(write in below, and keep this card for your reference)

This factory-assigned PIN cannot be changed or

deleted.

Keep this PIN information in a safe and secure loc-

ation.

Do not share the factory-assigned PIN with anyone.

Setting a User PIN

Although the factory-assigned PIN cannot be changed, a

custom

User PIN

can be added to the FUV. Once a User

PIN has been added, it can also be used to turn the FUV

on and off. Further, the User PIN can be changed at any

time.

Note that even after a custom User PIN has been added,

the factory assigned PIN also still works.

FUV Owner's Manual (REV 0) • last revised: 3/31/2022 • part# 006290 • doc ID: P10001

page 81

Summary of Contents for FUV 2022



































































































































































































Search results

Summary of Contents for FUV 2022

Reviews:

Related manuals for FUV 2022

Brands by name

Popular brands

ARCIMOTO FUV 2022, Owner'S Manual

Search results

Summary of Contents for FUV 2022

Reviews:

Related manuals for FUV 2022

Brands by name

Popular brands