Archtek telecom 5634BIF User Manual Download Page 37

Page: 37 / 49

5634BIF User’s Manual

time can be limited as it is a country dependent
parameter.

S-Register

Range

Default

Description

S30

0-255

tens of

seconds

(disable)

Disconnect Inactivity Timer

Sets the length of time , in tens of seconds, that
the modem will stay online before disconnecting
when no data is sent or will reset the timer. The
timer is inoperative in synchronous mode.

S31

194

BIT Mapped Options Status

Bit 0

¡ Ð

Single line connect message

enable/disable(\Vn)

0=Message controlled by S95,

Wn and Vn (\V0)(Default)

1= Single line connect message

(\V1)

Bit 1

¡ Ð

Auto line speed detection (Nn)

0= Disabled (N0)
1= Enabled (N1) (Default)
Bits 2-3

¡ Ð

Error correction progress messages

(Wn)

0= DTE speed only (W0)

(Default)

1= Full reporting (W1)
2= DCE speed only (W2)
Bits 4-5

¡ Ð

Caller ID(#CID)

0=Caller ID disabled (#CID=0)

(Default)

1=Short (formatted) Caller ID

enabled (#CID=1)

2=Long (unformatted) Caller ID

enabled (#CID=1)

Bits 6-7

¡ Ð

Reserved

S32

0 - 255

11, hex

Sets the value of the XON character

S33

0 - 255

13, hex

Sets the value of the XOFF character

S36

Bit

Mapped

Bit 0-2

07, hex

LAPM Failure Control

This value indicates what should happen upon a
LAPM failure.
0

Modem disconnect.

Modem stays on-line and direct mode
connection is established.

Modem stays on-line and a normal mode
connection is established.

An MNP connection is attempted and if it
fail, the modem disconnects.

An MNP connection is attempted and if it
fails a direct mode connection is
established.

Summary of Contents for 5634BIF


















































Search results

Summary of Contents for 5634BIF

Reviews:

Brands by name

Popular brands

Archtek telecom 5634BIF, User Manual

Search results

Summary of Contents for 5634BIF

Reviews:

Brands by name

Popular brands