manualshive.com logo in svg

Arcam A38, Handbook, Page: 16 / 18

Share
Download
Arcam A38 Handbook Download Page 16

e-16

a38

P38

Continuous power output (20Hz—20kHz at 0.5% THD), per channel
Both channels, 8

Ω

, 20Hz—20kHz

100W

100W

Single channel, 8

Ω

, 20Hz—20kHz

150W

150W

Both channels, 4

Ω

, 20Hz—20kHz

140W

140W

Single channel, 4

Ω

, at 1kHz

200W

200W

Harmonic distortion, 80% power, 8

Ω

 at 1kHz

0.005%

0.005%

Inputs

Phono input (optional module):
     Input sensitivity

2.7mV (MM); 270µV (MC)

     Input impedance

47k

Ω

 (MM); 300

Ω

 (MC)

     Signal/noise ratio (CCIR)

–79dB (MM); –73dB (MC)

     Overload margin

35dB

Line inputs:
     Nominal sensitivity

250mV—2V

800mV (pre-amp. in)

     Input impedance

10k

Ω

10k

Ω

     THD+n (1kHz, 0dB signal, measured 20Hz to 

20kHz unweighted)

–104dB

–104dB

Power amplifier input

Nominal sensitivity

800mV

800mV

Input impedance

22k

Ω

22k

Ω

Gain

31.5dB

31.5dB

Preamplifier output

Nominal output level

700mV

Maximum output level

2.6V RMS

Output impedance

<50

Ω

Headphone output

Maximum output level into 600

Ω

1.6V rms

Output impedance

4.7

Ω

General

Mains voltage

115V or 230V

115V or 230V

Power consumption (maximum)

800VA

800VA

Power consumption (standby)

2VA

2VA

Dimensions W x D x H (including feet)

430 x 370 x 110mm

430 x 350 x 110mm

Weight (net)

9.3kg

9.5kg

Weight (packed)

12.2kg

12.5kg

Supplied accessories

mains lead 

CR90 remote control 

4 x AAA batteries

mains lead 

E&OE
NOTE: All specification values are typical unless otherwise stated.

continual improvement policy

Arcam has a policy of continual improvement for its 

products. This means that designs and specifications 

are subject to change without notice.

specifications

Summary of Contents for A38



















Reviews:

No comments