ARC SKBLE-1927 Manual Download Page 20

5

. Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following 
two conditions: (1) This device may not cause harmful interference, and (2) this device 
must accept any interference received, including interference that may cause undesired 
operation.
Note: This equipment has been tested and found to comply with the limits for a Class B 
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide 
reasonable protection against harmful interference in a residential installation. This 
equipment generates, uses and can radiate radio frequency energy and, if not installed and 
used in accordance with the instructions, may cause harmful interference to radio 
communications. However, there is no guarantee that interference will not occur in a 
particular installation. If this equipment does cause harmful interference to radio or 
television reception, which can be determined by turning the equipment off and on, the user 
is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the 
receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Note: The Grantee is not responsible for any changes or modifications not expressly 
approved by the party responsible for compliance. such modifications could void the user's 
authority to operate the equipment.

The device has been evaluated to meet general RF exposure requirement.  
This equipment complies with FCC's RF radiation exposure limits set forth for an 
uncontrolled environment. This device and its antenna(s) must not be co-located or 
conjunction with any other antenna or transmitter.
 This device complies with Industry Canada license-exempt RSS standard(s).

 

Operation is subject to the following two conditions: (1) this device may not

 

cause 

interference, and (2) this device must accept any interference, including

 

interference 

that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux

 

appareils radio exempts de licence. L'exploitation est autorisée aux deux

 

conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2)

 

l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même

 

si le brouillage est susceptible d'en compromettre le fonctionnement.

The device has been evaluated to meet general RF exposure requirement. The 
device can be used in portable exposure condition without restriction.
L'appareil a été évalué pour répondre aux exigences générales 
d'exposition RF. le dispositif de a été évalués à répondre général rf 
exposition exigence.

20

Summary of Contents for SKBLE-1927





















Reviews: