background image

 

ARC-CDJPLAYER 

 

INSTALLATION MANUAL 

Full plug and play kit, universal fit for use in  

Chrysler vehicles with RA1, RA2, RA3, or RA4 radios.  

 

Required for Install:

 

 

1. Chrysler/Dodge/Jeep vehicle with Uconnect 3.0, 5.0, or 8.4” Touch Screen. 
2. ARC-CDJPLAYER Installation Kit 
 

Vehicle Applications: 

 

2013+ Ram Truck, Viper 

 

2015+ Charger, Challenger, 300 

 

2017+ Pacifica 

 

ARC-CDJPLAYER Kit Contents:

 

 

1.

 

ARC-CHRY52R2 T-Harness 

2.

 

5091217AD OEM Remote CD player 

3.

 

RAMROD-BRACKET (x2), RAMROD-CASE Universal case and mounting solution 

4.

 

PHWS812M(x4), PWHT812(x4) 4 Self drilling screws for mounting on metal, 4 stingers for plastic 

5.

 

24291 (x2) Stand-Off threaded spacers for use in Pacifica installation 

6.

 

RAMROD-EXT Remote CD Player Harness – 15 foot 

7.

 

257357C Configurable Module to enable CD Player – Does 

not

 require dealer programming 

 

 

Notice: 

**All information provided in this instructional guide is given on an as-is basis. All wires should be verified 

and tested for functionality before any connections are made. All wiring connections should be made using 

OEM approved wire repair techniques which include, but are not limited to, soldering and heat-shrinking all 

connections. When screwing or drilling, verify clearance on opposite side of work surface. Professional 

installation is recommended** 

Summary of Contents for ARC-CDJPLAYER












Reviews: