manualshive.com logo in svg

ARC Audio X2 1100.1, Owner'S Manual

Share
Download
ARC Audio X2 1100.1 Owner'S Manual Download Page 11

Page 11

X2 650.1 Specifications

Rated Continuous (RMS) Power into 4 Ohms at 14.4V

185 Watts x 1

Rated Continuous (RMS) Power into 2 Ohms at 14.4V

350 Watts x 2

Rated Continuous (RMS) Power into 4 Ohms at 14.4V

650 Watts x 1

Frequency Response (Subwoofer Channel)

20 Hz to 230 Hz

Crossover Range - Low-Pass

30 Hz to 230 Hz

Crossover Range - Subsonic

10 Hz to 80 Hz

Bass Boost (Sub Channel)

0 to 12 dB at 30 to 125 Hz

Remote Level Control Included

Yes

Input Sensitivity - RCA Input

200 mV to 3.5V

Fusing

2 x 30 Amp ATC/ATO

Dimensions

9.02”(L) x 6.268”(W) x 2.086”(H)

Start-Stop Vehicle Compatible

Yes (<8 Volts)

X2 1100.1 Specifications

Rated Continuous (RMS) Power into 4 Ohms at 14.4V

350 Watts x 1

Rated Continuous (RMS) Power into 2 Ohms at 14.4V

600 Watts x 2

Rated Continuous (RMS) Power into 4 Ohms at 14.4V

1100 Watts x 1

Frequency Response (Subwoofer Channel)

20 Hz to 230 Hz

Crossover Range - Low-Pass

30 Hz to 230 Hz

Crossover Range - Subsonic

10 Hz to 80 Hz

Bass Boost (Sub Channel)

0 to 12 dB at 30 to 125 Hz

Remote Level Control Included

Yes

Input Sensitivity - RCA Input

200 mV to 3.5V

Fusing

3 x 30 Amp ATC/ATO

Dimensions

13.0”(L) x 6.268”(W) x 2.086”(H)

Start-Stop Vehicle Compatible

Yes (<8 Volts)

X2 2500.1 Specifications

Rated Continuous (RMS) Power into 4 Ohms at 14.4V

900 Watts x 1

Rated Continuous (RMS) Power into 2 Ohms at 14.4V

1600 Watts x 2

Rated Continuous (RMS) Power into 4 Ohms at 14.4V

2500 Watts x 1

Frequency Response (Subwoofer Channel)

20 Hz to 230 Hz

Crossover Range - Low-Pass

30 Hz to 230 Hz

Crossover Range - Subsonic

10 Hz to 80 Hz

Bass Boost (Sub Channel)

0 to 12 dB at 30 to 125 Hz

Remote Level Control Included

Yes

Input Sensitivity - RCA Input

200 mV to 3.5V

Fusing

6 x 30 Amp ATC/ATO

Dimensions

20.92”(L) x 6.268”(W) x 2.086”(H)

Start-Stop Vehicle Compatible

Yes (<8 Volts)

Summary of Contents for X2 1100.1












Reviews:

No comments

Brands by name

Popular brands

Load more brands