background image

KS 1200.1

KS 1200.1

GND

TURN

ON

12V

+

KS 1200.1

KS 1200.1

GND

TURN

ON

12V

+

KS 1200.1

KS 1200.1

GND

TURN

ON

12V

+

KS 1200.1

KS 1200.1

GND

TURN

ON

12V

+

KS 1200.1

KS 1200.1

GND

TURN

ON

12V

+

KS 1200.1

KS 1200.1

KS 1200.1

KS 1200.1

KS 1200.1

KS 1200.1

KS 1200.1

KS 1200.1

KS 1200.1

KS 1200.1

SET PHASE TO

IN

SET INPUT TO

NORMAL

SET PHASE TO

OUT

SET INPUT TO

SLAVE

Input from

head unit

SPEAKER

IN

Output to

next “SLAVE”

amplifier

SET PHASE TO

IN

SET INPUT TO

NORMAL

SET PHASE TO

IN

SET INPUT TO

SLAVE

Input from

head unit

Output to

next “SLAVE”

amplifier

NOTE: 

This wire must run from Negative to 

Negative. You will be driving the speaker wit 
the 2 Positive outputs.

5

6

Bridging

Bridging is a way to combine the power of 2 channels into 1. When you wire the amp 
bridged you have a higher voltage differential b and -. That means MORE POWER. 
If you have 2 identical, properly designed mono amplifiers (They can not be a stereo amp 
that is bridged internally) you can bridge them together to create 1 channel.

Warning

When bridging any amp or amps, each channel sees half the ohm load. 4 ohms bridged is the 
same as 2 ohms stereo. 1 ohm bridged is equal to 1/2 ohm stereo. Check the compatibility of 
you woofers and amplifier before you begin.

KS 1200.1

s or K

S 2500.1

s in a bridged configuration must not be connected to a load 

lower then 2 ohms. 

For bridging to work both amplifiers must be playing exactly the same signal at exactly 
the same output level. To make this easier use the “MASTER” and “SLAVE”  as above but the 
slave amp must be set to “Out of PHASE”

Use the configuration below.

AUTO SENSE

The

 KS 1200.1 

and 

KS 2500.1 

uses a Patent Pending Auto Sense Turn-on circuit that 

offers a significant improvement in reliability over previous designs. Instead of relaying on 
the music to supply enough signal to turn the amplifier on. Robert Zeff’s new design 
detects the IC (chip) used in the vast majority of stock head units and amplifiers.

To use the Auto Sense feature on the simply connect the factory speaker wires to the High 
Level Input and watch it work. 

MASTER/SLAVE

The 

KS 1200.1

 and 

KS 2500.1

 are equipped with a MASTER/SLAVE circuit. This allows you to 

control 2 or more amplifiers from one set of controls. All of your gains, crossovers, bass boost, 
subsonic filter and remote level will be controlled from a single “master” amplifier. This 
eliminates all the tedious gain and crossover matching normally needed when using multiple 
amplifiers.

Summary of Contents for KS 1200.1









Reviews: