background image

 

Page 

5

 of 

5

 

 

which can be determined by turning the equipment off and on, the user is encouraged to try to correct the 
interference by one or more of the following measures:  

- Reorient or relocate the receiving antenna.  
- Increase the separation between the equipment and receiver.  
-  Connect  the  equipment  into  an  outlet  on  a  circuit  different  from  that  to  which  the  receiver  is 

connected.  

- Consult the dealer or an experienced radio/TV technician for help.  

 
 
FCC Radiation Exposure Statement:  
 
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This 
equipment should be installed and operated with minimum distance 20 cm between the radiator and your 
body.  
 
 
 
 

ISED Declaration of Conformity  

 
 
This  device  contains  licence-exempt  transmitter(s)/receiver(s)  that  comply  with  Innovation,  Science  and 

Economic  Development  Canada’s  licence

-exempt  RSS(s).  Operation  is  subject  to  the  following  two 

conditions: (1) This device may not cause interference. (2) This device must accept any interference, including 
interference that may cause undesired operation of the device.  
 
Cet appareil contient des émetteurs / récepteurs exemptés de licence conformes aux RSS (RSS) d'Innovation, 
Sciences  et  Développement  économique  Canada.  Le  fonctionnement  est  soumis  aux  deux  conditions 
suivantes:  (1)  Cet  appareil  ne  doit  pas  causer  d'interférences.  (2)  Cet  appareil  doit  accepter  toutes  les 
interférences, y compris celles susceptibles de provoquer un fonctionnement indésirable de l'appareil.  
 
 
ISED Radiation Exposure Statement:  
 
This modular complies with IC RF radiation exposure limits set forth for an uncontrolled environment. This 
transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.  
 
 
End product labeling:  
 
If the IC number is not visible when the module is installed inside another device, then the outside of the 
device into which the module is installed must also display a label referring to the enclosed module. This 
exterior label must 

use wording: “Contain

s IC: 8855A-

ARANETRM”

.  

 

Summary of Contents for TDSPRMU1






Reviews: