Aradex VECTOPOWER VP5000-DC Installation Manual Download Page 80

Page: 80 / 173

VP5000-DC/DC60, VP5000-DC/DC200-HL

Product description

Last edited 2019-02-08
by Sonja Scheunert

Filename
VP5000_DCDC60_200-HL_installation_manual_v1-4en.docx

80 / 173

•

The number of conductors per cable depends on the number of occupied pins.

•

The size of the conductors depends on the size of the respective crimp contacts.

•

The crimp contacts are supplied with the mating connector. The cable is not included in the
scope of delivery.

Description

Value

Conductor cross-section

0.5 - 1.5 mm² Cu / 16 - 21 AWG Cu

Maximum conductor diameter

Maximum current load per crimp contact

Table 42: Specifications of the cables for the crimp contacts for [ST4]

Relevant links for [ST4]

Link to the product catalog on the Intercontec homepage

Link to the assembly manual for series 923 on the Intercontec homepage

Summary of Contents for VECTOPOWER VP5000-DC














































































































































































Search results

Summary of Contents for VECTOPOWER VP5000-DC

Reviews:

Related manuals for VECTOPOWER VP5000-DC

Brands by name

Popular brands

Aradex VECTOPOWER VP5000-DC, Installation Manual

Search results

Summary of Contents for VECTOPOWER VP5000-DC

Reviews:

Related manuals for VECTOPOWER VP5000-DC

Brands by name

Popular brands