AR 10037086 Operating And Service Manual Download Page 17

 

 

WARRANTIES:  LIMITATION OF LIABILITY

 

 

Seller warrants (i) that seller has title to the goods sold and (ii) that Amplifiers (all parts excluding traveling 
wave and vacuum tubes), Antennas, field monitors, field probes, field analyzers, field analyzer processor units, 
system controllers, system interlock, power meters, leak detectors, RF conducted probes, RF conducted clamps, 
Multi-tone, EMI receiver systems, RF down converters, RF conducted immunity systems, conducted immunity 
accessories, radiated immunity test systems, safety meters, safety sensor heads, tripods, directional couplers, 
waveguide adapters, termination loads, load attenuators, impedance stabilization networks, and coaxial cables 
will be free from defects in material and workmanship for a period of three (3) years from date of shipment 
shown on AR RF/Microwave Instrumentation invoice.

 

All modules, used in the amplifiers for the 1-6 GHz, 4-18 GHz, 6-18 GHz, all HPM products, and other 
applications, are hermetically-sealed. This sealing process protects the internal hybrid circuitry from humidity 
that could compromise the long term reliability of the product.  These modules are not field-repairable and 
should 

never

  be opened outside of AR’s Microelectronics Lab.  The modules in these product lines have a 

security label on two sides of the modules between the housing and lid/cover. If the security label is removed 
and or cut, the warranty of the module will be voided. 

Vacuum tubes in the ‘L’ series amplifiers, traveling-wave tubes in TWT amplifiers, and power heads will be 
free from defects in material and workmanship for a period of one (1) year.  

Contact AR RF/Microwave Instrumentation for warranty information regarding items not listed.   

Seller’s sole responsibility in fulfilling these warranties shall be to repair or replace any goods which do not 
conform to the foregoing warranties or, at seller’s option, to give buyer credit for defective goods.  The warranty 
is valid only when used in the country specified at time of order.  Warranty service must be obtained from the 
repair facility designated at that time.  If warranty service is not available in the country where the equipment 
is to be used, it must be returned to AR RF/Microwave Instrumentation.  Warranty service will be provided 
only for defective goods which are returned within the warranty period, freight costs prepaid to AR 
RF/Microwave Instrumentation or its designated repair facility. 

There are no other warranties, express or implied, including any warranty of merchantability or fitness.  Seller 
shall not be responsible for any incidental or consequential damages arising from any breach of warranty. 

No person other than an officer of Amplifier Research Corporation, has any authority to bind seller to any 
affirmation, representation or warranty except as specifically included in the preceding terms and conditions. 

 
 

Rev 1216 

 

 

 

 

 

Summary of Contents for 10037086



















Reviews: