1.6 Installing the Media Player if an existing factory stereo is already installed
If replacing an existing Harley-Davidson
®
factory stereo
use the existing Harley-Davidson
®
factory side mounting
brackets and hardware to mount the Media Player.
1. Unplug the 23-pin harness and FM/AM radio antenna
from the factory stereo.
2. Remove the factory stereo and replace with the
AQ-MP-5BT-H Media Player using the existing factory
mounting hardware.
3. Plug the 23-pin harness and FM/AM radio antenna
into the AQ-MP-5BT-H factory stereo.
4. Turn the Media Player on to confirm operation (motorcycle ignition switch must be on) and
once correct operation is achieved turn the motorcycle ignition switch off before proceeding
with the final mounting of the chassis.
4. Ensure that the unit is supported and secured on the sides using the existing 4 factory
screws; failure to do so may allow the unit to move during while riding, causing damage to
the mounting area.
1.7 Connecting Rear Speakers
Rear speakers are usually installed on the following Harley-Davidson
®
Motorcycle models:
Electra
Glide Ultra Classic, Road Glide Ultra, Ultra Limited.
To continue using these speakers with your
Aquatic AV Media Player follow the instructions below.
1. Locate the Aquatic AV 4-pin pigtail connector (4-pin molex connector with four speaker wires).
The pigtail itself is labelled with Color Code, Function and Description.
2. Locate the stock 35-pin wiring harness that was connected to your OEM radio. This connector
will not be connected to your Aquatic AV head unit. Cut the four matching colored wires from the
back of the 35 pin harness 3” down from the connector.
3. Strip the 4-pin pigtail wires 1/4” exposing bare wires. Strip the 4 wires that you cut from the
35-pin harness 1/4” exposing bare wires.
4. Connect and crimp using crimp caps or solder the connection, cover the soldered wires with
non conductive heat shrink tube.
After following the installation instructions above test your rear speakers for sound. If you do not have output from your
rear speakers make sure to check your rear speaker setting in the settings menu and select rear speakers ‘ON’.
5.5 Stereo/Mono
Change the output mode between stereo and mono. Some applications only accept a mono input.
5.6 FM Tuning Area
The FM tuning can be set to different areas, using the rotary knob to scroll through to select the
desired tuning area.
There are seven different tuning areas: USA, EUR, LAT, ASIA, MIDDLE EAST, AUSTRALIA,
RUSSIA.
5.2. AS/PS (Auto Scan/Preset Scan)
Scans through the current frequency band, and assigns presets to the radio stations that have the
strongest signal strength.
Only does this for one AM/FM band at a time.
5.4 Local/Distant Tuning
When ‘Local’ is turned on the Media Player seeks to only the radio channels with strong signal
strength. When ‘Local’ is turned off the Media Player will seek to all radio channels it receives
signal from.
When local is turned on the word ‘Local’ will appear in the upper right hand corner of the Media Player LCD.
5.1 Audio Menu
From the ‘Audio Menu’ you are able to change the bass, treble, balance, and fader.
Any changes made in the ‘Audio Menu’ are system wide so it will affect all modes.
1. To enter the ‘Audio Menu’ press the ‘AUDIO/MENU’ button.
2. In the ‘Audio Menu’ press the ‘AUDIO/MENU’ button to scroll through all options.
3. To change the parameters use the rotary knob to adjust settings.
5.3. Clock Settings
From the clock settings menu you are able to adjust the time and switch the clock on or off.
1. To change the time press MENU then use the rotary knob to navigate to SYSTEM settings
then CLOCK SETTINGS. Use the rotary knob to adjust and set the time.
2. To switch the clock on or off press MENU then use the rotary knob to navigate to SYSTEM
settings then CLOCK PRIORITY. Use the rotary knob to select either ON or OFF.
Getting Started
Media Player AQ-MP-5BT-H
Settings Operation
Media Player AQ-MP-5BT-H
11
www.aquaticav.com/harley
www.aquaticav.com/harley
6
