Aquatic Nature aquachill 200 User Manual Download Page 3

Technical Products

Technical Products

Temp

35°C

30°C

25°C

20°C

6PM   9PM   12AM   3AM   6AM   9AM   12PM   3PM   6PM   9PM   12AM   3AM   6AM

Water volume 200 Liters

room temp
water temp

(without Chiller)

water temp

(with Chiller)

Cooling effect : for a 200 liter aquarium, at room temperature of 32°C ~ 

  38°C, it will take 12 hours to lower the water temperature with 5°C.

  ( The chart is for reference only, actual cooling will depend on the 

  surroundings of the aquarium ).

 ( see below )

Setup

- Press the ‘On’ button 

(fig. 30)

, a green light appears on the 

  AquaChill 200. While the AquaChill 200 is running, the cooling fan 

  could make a little noise.

 

- On top of the AquaChill 200 you’ll find a display 

(fig. 31)

 This display has 

  2 buttons, one with the arrow pointing upwards (red field), and one with 

  the arrow pointing downwards (blue field)

- The arrow in the red field is for choosing a higher temperature setting (for 

  example, if your display reads 25°C , and you wish to set the temperature 

  to 27°C, then use this arrow.)

- The arrow in the blue field is for choosing a lower temperature setting (for 

  example, if your display reads 25°C , and you wish to set the temperature 

  to 23°C, then use this arrow.)

- If the requested temperature is 25°C, yet the temperature of the aquarium 

  is higher  (for example 27°C), then the orange LED light goes on and the 

  cooling starts. In the opposite case, if the requested temperature is higher 

  than the water temperature, then the LED light goes off and the cooling 

  stops.

Maintenance

- Do not clean the AquaChill 200 body with water, but wipe it with a  

  dry cloth instead. 

(fig. 32)

 Do not disassemble the AquaChill 200,  

  the warranty then expires. 

- In case of insufficient air apport on the inlet or outlet of the 

  ventilator due to dust , clean it with a brush or vacuum cleaner

 

 (fig. 33), 

thus prolonging the lifetime and efficiency of the 

  AquaChill 200.

- When moving the AquaChill 200 or his Power source, ALWAYS  

  unplug the power cable first.

 (fig. 34)

The AquaChill 200 has a very low maintenance, yet a few rules 

have to be applied :

- Check the tubing of the water in- and outlet regurarly (once every 6 

  months). If they are dirty, replace them.

www.aquatic-nature.com

www.aquatic-nature.com

Summary of Contents for aquachill 200








Reviews: