background image

WARNING:

Faucet will leak 
if restrictor is 
not installed

6 — CONNECT TUBING

I: Brass Tee to Manifold “INLET”  

(1/4" white tubing)

 

1

  Take the white tubing leading from the brass tee and insert it into the manifold port 

labeled “INLET”. Remember to push it all the way in until it stops.

II: Manifold to Faucet 

(3/8" white tubing already attached to faucet) 

Insert the 3/8" white tubing (that was installed in step 4) from the faucet into the manifold 

port labeled “FAUCET”.

III: Manifold to Tank

 

(3/8" white tubing already attached to tank) 

 Take the white tubing leading from the storage tank and insert it into the manifold port 
labeled “TANK”. Remember to push it all the way in until it stops.

IV: Air Gap to RO Membrane

 

(1/4" red tubing from faucet) 

Insert restrictor into the end of the red tubing. 

2

 Attach 1/4" red tubing to the 90° elbow until it stops. 

Attach 1/4" 90° elbow to the membrane drain port.

V: Faucet to Drain Connector

 

(3/8" red tubing from faucet) 

  Take the 3/8" red tubing from faucet and insert it all  

the way into the drain connector.

COLD

Hose Connections:

 

¼" White  Brass Tee to Manifold

 

3⁄8" White  Manifold to Faucet

 

3⁄8" White  Manifold to Tank

HOT

I

I

II

III

 

¼" Red 

Membrane to Faucet

 

3⁄8" Red 

Faucet to Drain Connector

IV

V

IV

II

III

V

OptimH2O™

Stage 2

RO Membrane

AQ-RO3-RO

OptimH2O™

1

2

3

0.95”

Tube Marking Guide:

(actual size)

Tubing Dont’s

DO NOT cut tubing too short. Always double check 

measurements before cutting.
DO NOT bend or crimp or kink tubing.
DO NOT discard excess tubing.

Tubing Do’s

Insert tubing ALL THE WAY IN to prevent 

leaking. In most cases, up to nearly a full inch.
Wet end of tubing to more easily insert into all 

inlets and outlets.
Cut excess tubing in order to prevent crimping, 

kinks, loops or folds.

Summary of Contents for OptimH2O AQ-RO-BASE










Reviews: