Aquamonitor GreenStar Quick Start Manual Download Page 3

Pre-Installation 

 

Installing Display Unit 

Choose a location for the Display Unit, which must be within 

wireless range of the sensors.  The wireless range will depend 

on the presence of objects, such as walls and vegetation, 

between the Display Unit and each sensor.  

 

The Display Unit can be 

wall mounted using the wall 

bracket.  To place it on a 

bench remove the wall 

bracket and rotate the foot- 

stand outwards. 

Wireless range is usually 

best when the sensor and 

Display Unit are located 

away from the ground and 

the antenna is not sitting 

on a surface. 

Step 1: Unpack the Display Unit and connect the DC power 

adaptor to the Display Unit and switch the power on at the 

wall.  Use the buttons to set the time and date and day of 

week.  Answer NO to the question to clear values.  

Step 2: Referring to the Menu Guide, enter the menu system 

by pressing the OK button.  Use the menu to set the number 

of users, Tank height and volume  and alarm settings.  The 

date and time can also be changed if needed.

  

Battery Insertion – Tank Sensor 

Step 3: Fit the AA batteries and check the polarity (+ and -) 

which is shown inside the battery cover. Once the batteries 

are in place, push the battery compartment cover back on 

whilst observing the LED through the recessed hole in the 

cover and check that it flashes briefly. If the LED indicator 

doesn’t flash then check the orientation and type of battery 

used. 

 

Check Wireless Connection 

 

Step 4: Observe the Display Unit after a few minutes to check 

that a wireless connection has been established.  

 

 

Step 5: Use the Display Unit menu to enter the height of the 

tank from the bottom of the tank to the roof, in millimeters.  If 

the roof is sloped then measure from the outside edge of the 

roof (the lowest point of the roof) to the bottom of the tank. 

Step 6: Next, enter the tank size in litres.  Some tanks may 

have this stamped on the roof or you may obtain the capacity 

from the tank manufacturer or supplier.  If this information 

cannot be found then please contact Aquamonitor Support. 

Tank Sensor Installation 

 

The Tank Sensor mounts to the top (roof) of the tank on the 

outside. The best location is toward the middle of the tank 

and/or at the highest point of the tank and away from the 

edges. Ensure that the location of the sensor has a clear line 

of sight to the bottom of the tank. Internal structures between 

the sensor and the bottom of the tank will limit the 

measurement range.  

 

Before fitting the Tank Sensor to the top (roof) of the tank, 

place the sensor in the desired location and check the wireless 

connection to Display Unit.  

 

Placing and Securing Tank Sensor 

 

Step 1: Check that: 

 

There is a wireless connection with the Display Unit. 

 

The sensor is not near side of the tank (more than 

500mm). 

 

The distance from the maximum water level and the 

sensor is at least 300mm. 

 

There is a clear line of sight to the bottom of the tank. 

 

Step 2: The Tank Sensor has been designed to allow for tanks 

with a sloped roof.  When fitting the sensor, position the unit 

across the gradient of the tank. This will allow the angle to be 

set to counter for the gradient. 

  

Step 3: Using the drilling template supplied, provide the 

mounting holes in a removable lid or in the roof of the tank. 

Remove the battery cover from the sensor. 

 

Step 4: Fit the P clips to the sensor head first then screw the 

P clips into place around the centre hole.  

 

Step 5: Observe the spirit level guide and adjust the level to 

vertical before tightening the screws holding the P clips.  

 

 

 

 

Step 6: Fold the top half of the sensor over to cover the 

sensor head and fasten the body of the sensor to the roof of 

the tank using four screws and refit the battery cover. 

Reviews: