Tank Monitor Quick Start Guide
Revision A August 2012
Thank you for purchasing an Aquamonitor product.
Please read this guide carefully and keep it for future
reference. The details included in this guide, such as
pictures, symbols and descriptions are for reference
only and may not exactly represent the physical detail
of your item. This is because we are continually
updating and improving Aquamonitor products and so
features, technical specifications and physical
appearance are subject to change.
Safety and Usage Precautions
Please read and understand all instructions contained in this
guide prior to installation and use. If clarification or further
details are needed, contact us at
www.aquamonitor.com.au
.
This product is a radio transmitting device and may cause
interference with sensitive electronic equipment such as audio,
visual, vehicle and medical equipment and systems.
This product is also a radio receiving device and may be
affected by other equipment or systems that emit radio
frequencies, such as two-way radios, wireless remote
controllers and in-home wireless products.
Always ensure safe working conditions during installation. If
using a ladder, make sure it is on firm and level ground and
that a second person is holding it steady.
Only use the DC power adaptor supplied with the Display Unit.
Do not use other types as this may damage the electronics.
The Display Unit is not waterproof and contains sensitive
electronic circuitry. Use it only in dry, cool environments.
The Display Unit and sensors operate at low radio power levels
to ensure good battery life. Locate the Display Unit as close
as possible to the sensors to ensure wireless operation. Avoid
locating the sensors or Display Unit within or near metallic
structures. Ensure that there is clear space around the
sensors and Display Unit to allow the radio signals to
propagate. Install the sensors in locations away from areas
that fill or pool with water.
When replacing batteries please ensure that the batteries are
the type specified in this guide. The sensors will not operate
and may be damaged if the battery voltage is incorrect.
If this product does not operate normally then refer to the
troubleshooting information contained in this guide. There are
no operator serviceable parts inside aside from batteries.
Please refer servicing and repair to qualified service personnel
or seek support through the Aquamonitor web site.
The Aquamonitor Tank Sensor is designed to suit a variety of
tank styles and types. Please check that your tank height is
within the range limits as detailed in the Specifications. The
Tank Sensor requires a clear line of sight to the water surface
from the top of the tank and objects within the path of the
sensor to the water surface will affect level readings.
All rights are reserved. No part of this document may be
photocopied, reproduced or translated into another language
without the written consent of Aquamonitor Pty Ltd.
The information contained within this manual is subject to
change without notice. Aquamonitor Pty Ltd shall not be liable
for errors contained herein or for consequential damages in
connection with the furnishing, performance or use of this
guide or of associated information.
General Specifications
Wireless range
50 metres line of sight
30 metres urban location
Operating temperature
5 to 45 Celsius
RF (radio) Output
10mW approx. 434 MHz
Battery Type
2 x AA 1.2V – 1.5V, 2200mAh
DC Power – Display Unit
5V DC, 200 mA
Tank level range
0.3 to 3.1 metres
LED Indicators
Sensor
LED flashes on battery insert
LED flashes every minute
Boot up OK
Wireless connection OK
Display Unit
All buttons blue
Arrow buttons stay on (blue)
OK button is red
OK button is green
OK button is flashing red
Wake mode
Stopwatch is running
Consumption above set limit
Consumption below set limit
Alarm condition
Features
•
Display of water consumption: daily, per person, average
and quarterly.
•
Graphical display of consumption: 24 hour consumption, 7
day consumption.
•
Configurable alarms: low tank level, time alarm
(prolonged usage), night-use alarm.
•
Status Bar display of date and time plus sensor wireless
connection status and sensor battery level.
•
Navigation bar with display of button functions.
•
Illuminated buttons for indication of consumption limit
and alarms.
Information Display
1 - Status Bar with sensor health indicators.
2 - Title Bar, describing the value displayed.
3 - Value displayed, updates every minute.
4 - Seven day history of the displayed value.
5 - Navigation bar showing button functions.
Button Operation – Navigation Bar
•
The function of each button is shown on the navigation
bar (see item 5 in the above figure).
•
The first button press will activate the backlight and
illuminate the buttons (blue). If there is an alarm then the
alarm sound will be cancelled
•
Pressing OK will activate the menu system which allows
display of graphs and changes to settings.
•
Please note that the stopwatch function only works with
Mains Sensors.
