Before commencing installation, it is essential that the instructions below are read and
understood and that you have all the necessary components (shown overleaf). Prior
to installation, ensure all additional guides supplied with this product are read and
understood.
Failure to install the product in accordance with these instructions may adversely affect
the warranty terms and conditions. Do not undertake any part of this installation unless
you are competent to do so. Prior to starting, ensure that you are familiar with the necessary
plumbing and wiring regulations required to install the product correctly and safely.
The Quartz Smart Valve
TM
must be isolated from the mains power supply prior to
installing the wired remote.
•
!
INSTALLATION
Prepare a suitable route and install the 10m low voltage data cable. On the Quartz
Smart Valve
TM
side, allow sufficient length for plugging into the Quartz
Smart Valve
TM
socket. On the wired
remote side we recommend a minimum length of 70mm including the connector plug.
Ensure the data cable is the correct way round as both ends differ in type of connection used.
Data cables must be protected by suitable sheathing or conduit in the event of servicing
and maintenance.
A cut out is provided in the back plate to facilitate surface sited cable entry if preferred.
•
!
2
Using the back plate as a template, mark the position of the fixing
screws and a Ø20mm hole for the data cable rear entry point.
Prepare suitable wall fixings to accommodate no. 8 non-rusting
countersunk head screws of a suitable length (not included).
1
Wiring diagram - single outlet
Apply a thin bead of silicone sealant in the mastic groove at
the rear of the mounting plate and pull the data cable through
before securing the back plate to the wall using suitable no. 8
non-rusting countersunk screws.
3
5
Locate the remote assembly onto the back plate with the
graphics in a diagonal position as illustrated. Rotate the remote
clockwise so the graphics are in the horizontal position to lock
the unit in place.
To release the remote, insert a small flat bladed
screwdriver into the small opening at the 7 o’clock
position to release the locking mechanism, and rotate the
remote face anti-clockwise.
Before any electrical adjustment is attempted, the
electricity supply must be turned off at the mains switch.
Electrical installation may only be carried out by a
qualified person.
•
!
6
The Quartz
Smart Valve
TM
features a secondary data cable socket
next to the main data cable connection for use with the remote.
Carefully snap and remove the entry pillar and connect the cable
into the socket as shown.
For wired remotes used in conjunction with divert products, the cable plugs directly into
the diverter.
Quartz™ divert wired remotes can only be used with divert products.
Please refer to the Divert Installation Guide for further information.
•
!
7
Prior to commissioning the wired remote, please refer to the installation instructions provided
with the main product to complete the installation of the Quartz
Smart Valve
TM
.
WIRED REMOTE
Commissioning
1. Reconnect the power supply to the Quartz
Smart Valve
TM
.
2. Turn the shower system on using the main controller.
The LED light ring will flash simultaneously with the remote light ring, until the desired
temperature has been reached. When both LED lights remain constant, turn the
shower off using the main controller.
3. Repeat the above process using the remote rather than the main controller ensuring
the LED lights flash and remain constant simultaneously.
User guide
Single outlet system
1. Press the button on the wired remote to turn the shower on.
2. The flashing to steady LED display advises when the
temperature selected by the main controller has
been reached.
3. Turn the shower off either by pressing the main controller
or remote button.
Dual outlet system
1. Press the button on the remote on the wired remote to turn the shower on.
2. The shower system will operate as determined by the outlet selected during the
diverter commissioning procedure.
3. If required, push and hold the remote button for 3 seconds to stop the 1st outlet and
start the 2nd outlet.
4. The flashing to steady LED display advises when the
temperature selected by the main controller has been
reached.
5. Turn the shower off either by pressing the main
controller or remote button.
After installation
Run through the wired remote operation with the user and hand them this guide, as well
as the main installation and user guide, if applicable.
Complete and post the guarantee card or register online at www.aqualisa.co.uk
Cleaning and maintenance
Your wired remote should be cleaned using only a soft cloth and washing up liquid.
DO NOT USE ABRASIVE CLEANERS
Cleaning and maintenance should not be undertaken by children without supervision
by a person responsible for their safety.
Quartz
TM
images shown for illustrative purposes only.
4
Lining up the key way, push the data cable plug into the back of
the remote assembly, ensuring both rubber skirts are recessed
into the connection (see diagram below), using a blunt flat bladed
screwdriver or similar tool if required. To make a water tight
fitting, ensure the rubber seal is no longer visible.
If fitting a Rise
TM
product, please refer to main Rise User Guide for further
operating instructions.
Although the Quartz Smart Valve
TM
complies with all relevant EMC standards, if incorrectly
sited, it may interfere with digital TV reception. Please follow the recommendations below to
minimise this effect.
If TV interference is an issue a service kit is available (part no: 652102).
See recommended layouts below.
Images of Quartz Smart Valve
TM
for illustration only, refer to main installation guide for orientation.
Valve colour may vary – the Original Quartz
TM
valve being black, and the Quartz Smart Valve
TM
being orange.
• Route cables separately, and as far apart from each other as possible.
• Aerial to point away from the Quartz Smart Valve
TM
.
• Ensure the distance between the Quartz Smart Valve
TM
and the aerial is as large as possible.
DIGITAL TV INTERFERENCE
AERIAL
LARGEST POSSIBLE DISTANCE
DATA
CABLE
POWER
CABLE
CABLE
TO TV
HIGH PROBABILITY
OF INTERFERENCE,
BOTH RADIATED
AND CONDUCTED
POWER
CABLE
CABLE
TO TV
DATA
CABLE
AERIAL
SHORT DISTANCE
LAYOUT WHICH COULD CAUSE PROBLEMS
LOWEST PROBABILITY OF INTERFERENCE
Wiring diagram - dual outlet
Quartz Rise Remote Installation Guide 704025 - Issue 2.indd 2
15/10/2018 12:37
