background image

2

INTRODUCTION & DESCRIPTION CHANGES

Thank you for purchasing the AquaCraft SuperVee 27R. We at 
AquaCraft want the time you spend with your boat to be safe, fun 
and successful. If for any reason you feel this R/C model is not for 
you return it to your place of purchase immediately. Your hobby 
dealer cannot accept returns on any model after fi nal assembly or 
after your boat has been operated.

AquaCraft products are to be used by ages 14 and over. 

All pictures, descriptions, and specifi cations found in this instruction 
manual are subject to change without notice. AquaCraft

 maintains 

no responsibility for inadvertent errors in this manual.

PARTS NEEDED TO COMPLETE YOUR MODEL

  4 – AA Batteries (transmitter)

For your convenience we have listed below a few different battery 
and charger options. Most 7.2V NiMH battery packs of around 
3000mAh or larger will work quite well in the SuperVee 27R. It is 
also important to note that chargers come in both DC and AC/DC 
versions. DC chargers require a 12V power supply like a 12V car 
battery or bench top power supply to power up the charger. AC/DC 
chargers allow you to plug the charger into a 120V house outlet or 
DC power supply, therefore making them more convenient for most 
charging situations.

OPTION 1:

 (This is about the minimum cost and performance one 

would need to own to operate your SuperVee 27R.)

  DTXC2054 Onyx

 3000mAh NiMH battery pack (2)–you need two 

battery packs to operate the boat.

  DTXP4002 Piranha DC Charger

OPTION 2:

 (This is a good middle of the road option; you will get 

good battery performance as well as an AC/DC charger.)

  DTXC2145 Onyx 3800 NiMH battery pack (2)

  DTXP4200 Onyx 200 sport peak charger

OPTION 3:

 (This option will provide the longest run times and best 

over-all performance, as well as allow you to charge both batteries 
at the same time.)

  DTXC2151 DuraTrax

®

 5000mAh NiMH battery pack (2)

  DTXP4240 Onyx Dual AC/DC charger

OPTIONAL PARTS

  GPMQ4480 Hook and Loop: Remember if you purchase extra 

battery packs you are going to need to purchase extra hook and 
loop as well.

  AQUB9700 40X52 3-bladed prop (this prop closely mimics the 

stock plastic prop but with better overall performance)

  AQUB9725 42X55 2-bladed prop (this prop has great acceleration 

as well as top speed)

  AQUB9514 Grimracer Pro Radio Box Tape (most top competitors 

tape shut the perimeter of the cowl to help keep water out of the 
boat)

  AQUB9500 Grimracer Speed Grease (you are going to need to 

re-grease the drive cable after each day of running)

  AQUB6322 Grimracer decal set (let them know that you’re ready 

to race!)

 Grimracer  says:

 Now is a good time to 

get your batteries on charge!

WARRANTY SERVICE

AquaCraft will warrant your SuperVee 27R for 90 days after the 
purchase from defects in materials or workmanship of original 
manufacture. AquaCraft, at their option, will repair or replace at 
no charge the incorrectly made part. This warranty does not cover 
damage caused by crash, abuse, misuse, alteration or accident. To 
return your boat for service you need to provide proof of purchase. 
Your store receipt or product invoice will suffi ce. 

IN NO EVENT SHALL THE PURCHASER BE ENTITLED TO ANY 
INCIDENTAL, SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES, 
WHETHER RESULTING FROM THE USE, MISUSE OR INABILITY TO 
USE THE PRODUCT OR FROM DEFECTS IN THE PRODUCT. 

This warranty gives you specifi c legal rights and you may also have 
other rights, which vary from state to state.

Outside USA and Canada, contact local importer for warranty 
information.

Hobby Services 

3002 N. Apollo Drive, Suite 1

Champaign, Illinois 61822

Attn: Service Department

Phone: (217) 398-0007 9:00 am - 5:00 pm Central Time M-F

E-mail: [email protected]

Summary of Contents for SuperVee 27R

















Reviews: