background image

5

3.  After removing the cowl, grab the bar on the top of the 

round opening covers and rotate to remove the covers.

4.  Plug the charger into an automobile’s 12 volt power outlet. 

Once the charger is plugged in it will start to beep and 
the light on the front will begin to fl ash. Place the charger 
outside your automobile.

5.  Join the battery and charger connectors. The connectors 

are designed to only connect one way to prevent the 
battery from being hooked up backwards.

After you attach the battery to the charger the beeping 
will stop and the light will stay illuminated to indicate the 
charger is charging property. It’s a good idea to check the 
battery pack every fi ve minutes or so. If at anytime the 
battery becomes hot, remove the battery from the charger. 
Allow the battery to cool completely before attempting to 
use it. When the charge is complete the charger will start 
to beep and the light will fl ash. 

Note: It is normal for the battery to be warm after charging 
it. It’s also a good idea to allow the battery to cool before 
placing it in the boat.

After charging is completed, unplug the charger from 
the power outlet. Disconnect the battery and charger 
connectors by pushing the small tab on down while gently 
pulling the connectors apart.

IMPORTANT PRECAUTIONS

•  Do not charge the battery with the vehicle’s engine 

running.

•  Always place the battery and charger outside the vehicle 

when charging.

•  Charge only the Mini Rio’s 6-cell 7.2 V 1100 mAh NiMH 

rechargeable battery. Do not attempt to charge other 
battery types, as damage may occur to the battery 
and charger.

• Do not allow water or foreign objects into the charger.

•  Do not cover the air intake vents on the charger as this 

can cause the charger to overheat and become damaged.

•  Do not leave the charger unattended while charging. 

Disconnect the battery immediately if the charger and/or if 
battery become hot.

• Do not charge hot batteries.

• Keep out of the reach of children.

6.  Install the hook and loop to the battery and install the 

battery in the boat. You will notice the plug can only be 
attached one way. Pay attention to the polarity of the 
plug. Plug the battery into the RX/ESC combo unit.

7.  Tuck the battery plug under the deck of the boat to keep 

the wires away from the drive components. 

Make sure 

the battery pack and wire are NOT touching the drive 
components.

Summary of Contents for Mini Rio









Reviews: