Aqua Simpool Pool-T, Instruction Manual

Page: 53 / 72

Simpool Pool-T Model INSTRUCTION AND MAINTENANCE MANUAL
Programmable digital peristaltic pump
ENGLISH
ADSP7000642 rev. 1.0 13/01/2014 53/72

Chose the Data Input Mode dIn of the Dosing Cycle Operation mode: to enter and exit the submenu, use
the Enter
key, to browse through the “
tIn/ G.nC
” entries use ▲
and
▼. This section of the Menu will not be
displayed if the Relay mode has been selected from the previous rEL entry;

Set the duration of the Delay Phase for the programmable cyclic mode, dlt , within a range from 0
(deactivated) to 999 seconds: to enter and exit the submenu, use the Enter key, to browse through the
values use
▲
and
▼. This section of the Menu wil
l not be displayed if the Relay mode, has been selected
from the previous rEL entry;

Set the duration of the dosing Phase for the programmable cyclic mode, do.t , within a range of 1-99
minutes. To enter and exit the submenu, use the Enter key, and browse through the values with
▲
and
▼.
This section of the Menu will be displayed if the Relay operating mode, rEL , has not been selected, and the
data input mode is equal to tIn ;

Set the amount of product to be dosed in g/cu. m. of water for the programmable cyclic mode, G.nC , within a
range of 0-99.9/ 100-999. To enter and exit the submenu, use the Enter key, and browse through the values
with
▲
and
▼. This section of the Menu will be displayed if the Relay operating mode,
rEL , has not been
selected, and the data input mode is equal to G.nC ;

Set the density of the product to be dosed, dEn , for the programmable cyclic mode, expressed as the
difference from the reference value of 1000 g/l, within a range of -50
÷
500, i.e. from 950 g/l to 1500 g/l: To
enter and exit the submenu, use the Enter key, to browse through the value use the keys
▲
and
▼; this
entry of the Menu will be displayed in case the Relay mode has not been selected through rEL , and the data
input mode is equal to G.nC ;

Set the capacity of the pool in cu. m. P.nc , within a range of 1-999. To enter and exit the submenu, use the
Enter key, and browse through the values with
▲
and
▼. This section of the Menu will be displayed if the
Relay operating mode, rEL , has not been selected, and the data input mode is equal to G.nC ;

Set the duration of the Block Phase for the programmable Cyclic Mode, bL.t , within a range of 0
(deactivated) - 99 minutes. To enter and exit the submenu, use the Enter key, and browse through the
values with
▲
and
▼. This section of the Menu will be displayed if the Relay operating mode,
rEL , has not
been selected;

Select if the cyclic programmable mode must be Repeat (see Operation section, Chap. 3.1) r.St : to enter
and exit the submenu, use the Enter key, to browse through the values use
▲
and
▼. This section of the
Menu will not be displayed if the Relay mode, rEL has been selected;

Set the stabilization time of the inhibiting signal, Stb , coming from the swimming pool recirculation pump,
within a range of 1-999 seconds: to enter and exit the submenu, use Enter , to scroll through the values use
the ▲ and ▼ keys;

Set the time of the pump maintenance alarm, O.F.d , from 0 (disabled) to 999 hours, based on the following
format:
- h.mm up to 9 h and 59 m
- hh.m up to 99 h and 59 m (minutes expressed in tens)
- hhh up to 999 h
To enter and exit the submenu use Enter and increase/decrease the value with the
▲
and
▼ keys;

Access the In.t inhibiting signal recognition window: to enter and exit the submenu use Enter . The display
will show the status identified by the pump for the input signal:
Steady "HI" : enabling signal identified as active;
Steady "Lo" : enabling signal identified as not active;
Flashing “HI”:
enabling signal identified as active, but slightly above the identification voltage threshold;
Flashing "Lo": enabling signal identified as not active, but slightly below the identification voltage threshold;
If the status displayed does not correspond to the actual status of the signal or if the status displayed is
flashing, just scroll with the
▲
and
▼ keys to change the threshold, namely:
Status of the non-active signal (recirculation pump OFF):

if the signal is identified as active (steady or flashing HI ) or not active but near the threshold (flashing Lo ),
press ▼ to reduce the threshold voltage until a steady “
Lo
” is displayed;

if the signal is permanently identified as not active (steady Lo ), conduct a check when the signal is
activated;