background image

QC SERIES SURFACE MOUNTED LED LIGHTS FOR CONCRETE POOLS – INSTALLATION INSTRUCTIONS & OWNERS MANUAL

QC SERIES

SURFACE MOUNTED LED  

LIGHTS for CONCRETE POOLS

Marking Line

Diagram 1

Item Description

Item Description

1

Universal Mounting Bracket 

4

Cable, assembled with Quick Connect Plug

2

Mounting Screws x 3

5

Cable Cap

3

LED Light Only

6

Quick Connect Plug

INSTALLATION INSTRUCTIONS

1)

  A rigid PVC conduit (min. 20mm diameter) should be run from the pool wall back to the plant room, where the 

transformer will be located. The conduit should be installed as to prevent water siphoning from the pool. The 

location of the pool light should be in such a position to allow enough cable to be wound up at the rear of the light 

to enable it to be floated to the pool deck. A location should also be chosen that minimises any shadowing from  

the light beam.

2)

  The Universal Mounting Bracket can be rendered to the pool wall or screwed directly on top of the pool interior, 

either way ensure the bracket is oriented correctly. The word “TOP” is moulded into the bracket.

When pebblecreting, plastering or rendering:

 Cover the circular frame of the 

Mounting Bracket with the finished pool surface up to the marking line on the three 

mounting posts. After the pool surface has been applied, only the 3 mounting posts  

will be visible. 

When screwing directly onto pool wall:

 Drill 4 holes in pool wall, aligning with the 

four screw hole provisions marked in RED in Diagram 1. Use the APL071 Retro-Fit 

Screw Kit (see page 3, item 7) available for purchase as an optional extra.  

Note:

 Trim Back the three mounting posts by 5mm, which will then enable the rear of 

the clear lens to sit against the interior pool surface.

3)

  The Cable can be fed through at a convenient time throughout the construction, it is factory-fitted with a protective 

Cable Cap to protect the electrical connector and O-rings from moisture, dust and grit. As mentioned above, ensure 

enough cable is left for future servicing.

4)

  When the pool is ready to be filled, then the Quick Connect Plug Kit is now ready to be inserted into the receptacle 

on the rear of the QC Series Led Pool Light. Unscrew and save the three screws that are securing the Cable Cap to 

the Cable Bracket. Remove the Cable Cap by disengaging the two clips on the Cable Bracket. The two O-rings are 

factory-lubricated, ensure they are free from dust and grit. Align the Quick Connect Plug Kit with the exposed metal 

pins in the receptacle on the rear of the QC Series LED Pool Light 

and push into place. Push the Cable Bracket towards the light until 

the clips engage into place. Use a #1 Phillips screwdriver and three 

screws (saved from above) and secure the Cable Bracket into the 

three screw holes. Do not overtighten. See Diagram 2.

5)

  Wind up excess cable around the hooks on the rear of the QC Series 

LED Pool Light. Use the three PE6 screws provided to mount the 

QC Series LED Pool Light onto the three posts on the Universal 

Mounting Bracket.

Diagram 2

INCLUDED WITH THE QC SERIES LED POOL LIGHT FOR CONCRETE POOLS:

2

Additional parts 

diagram is shown 

on Page 3.

1

2

3

4

5

6

TOP

Summary of Contents for QC Series

Page 1: ...g on an isolation transformer that has a number of secondary windings Aqua Quip s transformers allow multiple QC Series LED Lights to be connected refer to TRANSFORMERS info panel on page 4 QC SERIESSURFACE MOUNTED LED LIGHTS for CONCRETE POOLS TECHNICAL SPECIFICATIONS AQUA QUIP QC SURFACE MOUNTED LED POOL LIGHTS Power Requirement for Fixed Colour and Multi Colour LEDs 12V 32V AC 50 60Hz Pool Ligh...

Page 2: ...agram 1 Use the APL071 Retro Fit Screw Kit see page 3 item 7 available for purchase as an optional extra Note Trim Back the three mounting posts by 5mm which will then enable the rear of the clear lens to sit against the interior pool surface 3 The Cable can be fed through at a convenient time throughout the construction it is factory fitted with a protective Cable Cap to protect the electrical co...

Page 3: ...transformer s and junction box es This information is necessary if future servicing is required QC SERIES LIGHT PARTS DIAGRAM Diagram 3 3 QC SERIES LED LIGHT PARTS LIST LIGHT ONLY CODES A APL 802 Cable Hook J ASN 611 Female Pin Kit 3 LED 021 QC Blue Light B ASN 366 Cable Nut K ASN 362 Female Plug 3 LED 022 QC White Light C ASN 367 Washer L APL 803 Cable Cap 3 LED 023 QC Green Light D ASN 374 Blue ...

Page 4: ... 50 000 hours Variable Voltage Technology Each QC Series Light is able to be operated from a supply voltage ranging from 12 Volt AC through to 32 Volt AC For retro fitting the existing transformer will not have to be replaced saving money Amazing LED Colours Choose from fixed colours of white blue or green for maximum illumination or the Multi Colour option which incorporates the advanced Spectrum...

Reviews: