Aqua One Cabinet 53446 Assembly Instructions Manual Download Page 2

Safety Care and Advice

IMPORTANT: Please read these instructions before starting assembly

• Warning: This unit is heavy. 

Please lift with care.

• Check you have all the components 

and tools listed.

• Remove all fittings from the plastic  

bags and separate them into their 

groups.

• Keep children and animals away from 

the work area, small parts could choke 

if swallowed.

• Parts of the assembly will be easier 

with 2 people.

• Make sure you have enough space

 to layout the parts before starting.

• Assemble the item as close to its 

final position (in the same room) as 

possible.

• Assemble on a soft level surface to 

avoid damaging the unit or your 

floor (use opened  out unit carton).

 

 

• We do not 

        

 

recommend the use  

 

 

of power drill/   

 

 

drivers for inserting  

 

 

screws, as this could  

 

 

damage the unit. 

Only use hand screwdrivers.

• Dispose of all packaging carefully and 

responsibly.

Care and maintenance

Contact Us

• Only clean using a damp cloth and 

mild detergent, do no use bleach or 

abrasive cleaners. 

• From time to time check that there 

are no loose screws on this unit.

• This product should not be discarded 

with household waste. Take to your 

local authority waste disposal centre.

Aqua Pacific UK Ltd.

Unit 1, Mauretania Road, Nursling 

Industrial Estate, Southampton

SO16 0YS

Tel +44 (0) 2380 734000

Fax +44 (0) 2380 740200

[email protected]

www.aquaone.co.uk

Tools

Measuring 

Tape

Spirit Level

Cross-head 

screwdriver

Hammer

Eye protection 

(when using a 

hammer)

Silicone

Silic

one

Summary of Contents for Cabinet 53446












Reviews: