manualshive.com logo in svg

Aqua Lung Mistral Mouthpiece, Service Manual

Share
Download
Aqua Lung Mistral Mouthpiece Service Manual Download Page 10

 
10 

                                                Mistral Mouthpiece Service Manual 

 

 

Table 3. Recommended cleaners and lubricants 

 
 
 

 

LUBRICANT / CLEANER 

 

 

APPLICATION 

 

SOURCE 

 
Cristo-Lube MCG 111 
 
 
 
 
 
 
 

 
All O-rings 

 
Aqualung, ref. 480025 
 
 

 
Oakite #31 

 
Acid bath for cleaning brass and stainless 
steel parts.   
 

 
Oakite Products, Inc. 

 
NETALU 
 

 
Acid bath for cleaning brass and stainless 
steel parts.   
 

 
Aqualung, ref. 455001 

 
Diluted white vinegar 

 
Acid bath for cleaning brass and stainless 
steel parts.   
 
 
 
 
 
 
 

 
Household stores 

 
Washing-up liquid (diluted with hot water) 

 
Degreases brass and stainless steel parts; 
general cleaning of plastic and rubber 
parts. 
 

 
Household stores 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Attention: Silicone parts do not require lubrication.  Do not grease them. Greasing silicone 
parts can change their molecular construction and cause premature degradation of the material. 

Attention: Do not use hydrochloric acid for cleaning parts. Hydrochloric acid, even when well 
diluted, attacks the coating of metal parts and leaves a corrosive deposit that damages plastic 
parts and O-rings.   

Summary of Contents for Mistral Mouthpiece















Reviews:

No comments

Brands by name

Popular brands

Load more brands