Aqua Creek Products Revolution F-702RLNA-03 Manual Download Page 9

Copyright © 2019 Aqua Creek Products All Rights Reserved

Revised 6/19/19

FOOTREST

TUBE

(ADJUSTABLE)

SEAT

ASSEMBLY

PLASTIC

SLEEVE

1/4" FLAT WASHER

1/4" LOCK WASHER
1/4" X 1/2" BUTTON

HEAD BOLT

24V

BATTERY

CONTROL

BOX

HANDSET

CONTROL

 

 

Revolution Assembly Instructions

STEP 6: INSTALL THE FOOTREST

Locate the FOOTREST ASSEMBLY and install it on the 

seat as shown below. Slide the footrest tube into the 

square tube that supports the seat until the plastic 

sleeve of the footrest sits fl ush with the face of the 

square tube.  The threaded hole of the plastic sleeve 

should align perfectly with the hole in the bottom of 

the square tube.  Install the 1/4” button head, lock 

washer and fl at washer through the bottom of the 

square tube and up into the plastic sleeve.

STEP 7:

 INSTALL 24V BATTERY & HANDSET

Locate the 24V battery, the battery charging unit 

and the handset control. Charge the battery for 24 

hours then install it on the bracket above the control 

box as shown on PHOTO 7. Plug the handset control 

into the control box as shown in the fi gure and in 

the photos below. Press fi rmly to make sure the plug 

is fully seated as shown below. 

THE LIFT WILL NOT FUNCTION IF THE HANDSET 

PLUG IS NOT FULLY SEATED OR IF THE BATTERY IS 

NOT PROPERLY ALIGNED.

With the lift completely assembled, run the lift fully 

out and back in 3-5 times, without weight, for the 

lifts “break in” cycle period.

STEP 6

STEP 7

Seated

Not Seated

9

Summary of Contents for Revolution F-702RLNA-03















Reviews: