AQ-Tron LAD/AQ2000 Manual Download Page 11

MANUAL

www.aqtron.com - [email protected]

®

LAD/AQ2000

 

10 

used device, please use the return and collection systems or contact the retailer 
where the product was purchased. They can take this product for environmental safe 
recycling. 

 
 
 
 
 
 
 
WARRANTY

 

1) This product is warranted to the original purchaser for a period of two (2) years from the 
original shipping date, to be free of defects in material and workmanship.   
2) Warranty Performance: During the above two (2) years warranty period, a product with 
a defect will be replaced with a new one when the product is returned to the manufacturer. 
The replacement product will be in warranty for the balance of the original two (2) years 
warranty period. 
3) This warranty is void if the product has been damaged by accident, in shipment, 
unreasonable use, misuse, neglect, improper service, commercial use, repairs by 
unauthorized personnel or other causes not arising out of defects in materials or 
workmanship. 

Important safety instructions 

1)This appliance is not intended for use by persons (including children) with reduced 
physical, sensory or mental capabilities, or lack of experience and knowledge, unless they 
have been given supervision or instruction concerning use of the appliance by a person 
responsible for their safety. 
2)Children should be supervised to ensure that they do not play with the appliance. 
3)If the supply cord is damaged, it must be replaced by the manufacturer, its service agent 
or similarly qualified persons in order to avoid a hazard. 
3)The battery terminal not connected to the chassis has to be connected first. The other 
connection is to be made to the chassis, remote from the battery and fuel line. The battery 
charger is then to be connected to the supply mains;After charging, disconnect the battery 

Summary of Contents for LAD/AQ2000













Reviews: