background image

25 

 

Original operating manual ES 100 M1 Classic 

Quality for Professionals 

12   Maintenance and care 

12.1  General information 

To maintain the implement in good condition even after a long service life, the 
following instructions must be observed: 
 

 

Original parts and accessories are designed especially for the machines or 
implements. 

 

Please note that spare parts and accessories not supplied by us have also not 
been tested and approved by us. 

 

The installation or use of such products can therefore possibly negatively change 
or impede the constructional properties of your implement. The manufacturer 
rules out any liability for damages resulting from the use of non-original parts and 
accessories. 

 

The manufacturer is not liable for any unauthorised modifications and the use of 
components and auxiliary parts. 

 

All bolted connections should be re-tightened at the latest after 3 operating hours 
and again after 20 hours, and then checked regularly. (Loose bolts can cause 
significant consequential damage, which is not covered by the warranty.) 

 

Do not clean the implement with water. Clean the implement with compressed 
air, however, make sure that the pressure is not too high. The paint can be 
damaged by cleaning with excessive pressure. 

 

Park the implement protected from weather conditions. 

 

During the winter, the implement should be protected against rust with an 
environmentally-friendly product. 

 

13  Storage and disposal 

To ensure that the spreader remains fully functional even if it is out of operation for 
longer periods of time, it is important to take precautions for storage. 
 
This is how to prepare the spreader for storage: 
1.  Completely remove all seed from the spreader. 
2.  Clean the spreader inside and out. 
3.  Store the spreader in a dry place to prevent the formation of germs inside the 

implement. 

 
The spreader must be stored in a dry place protected from weather conditions to 
ensure that it remains functional even if it is stored for a longer period of time. 
 
 
Disposal of the spreader must be performed according to the local disposal 
regulations for machines. 
 

 

 

Summary of Contents for ES 100 M1 Classic

































Reviews: