background image

39

use and maintenance Scarabeo 50 

 - Scarabeo 100 4T

6

Press the start push button “

” (5), rotate

the throttle twistgrip by 1/8 of its turn (see
figure), and then release it as soon as the
engine starts.

When the start push button “

” is

pressed, the mixer oil reserve warning
light “

” comes on.

With the engine in running condition,
when the start push button “

” is re-

leased, the mixer oil reserve warning light

” must go out; if this does not occur,

top up the mixer oil tank, see page 28
(MIXER OIL).

100

 If the “injection check” warning light

comes on after the engine has started,
stop the vehicle and contact an 

aprilia

Official Dealer.

Avoid pressing the start push button “

(5) when the engine is running, since you
may damage the starter.

KICK START 

100

Position the vehicle on the centre stand,
on a solid and level surface.

Move to the left side of the vehicle.

Make sure that the light switch (1) is in
position “ 

 ”.

 Make sure that the dimmer switch (2)

is in position “

”.

Move the ignition switch (3) to position

”.

CAUTION

CAUTION

To avoid losing control of the vehicle dur-
ing the starting, lock both wheels by
putting on the brake levers (4).

Rotate the kick starter outward (6).

Do not push down the kick starter with
the engine on.

Push down the kick starter (6) with your
right foot, releasing it immediately.
If necessary, repeat the operation until the
engine starts.

Let the kick starter go back to home posi-
tion (6).

Summary of Contents for SCARABEO 100 4T - 06-2001 PART7





















Reviews: