manualshive.com logo in svg

APRILIA RS 660, Service Station Manual, Page: 101 / 420

Share
Download
APRILIA RS 660 Service Station Manual Download Page 101

TABLE J - PROCEDURE FOR THE CORRECT

FITTING OF THE ABS CONTROL UNIT CON-

NECTOR

•

Pass the ABS modulator wiring as in-

dicated.

Components present:

1) ABS modulator wiring

2) ABS modulator connector

TABLE J1 - PROCEDURE FOR THE CORRECT FITTING OF THE ABS CONTROL UNIT CONNEC-

TOR

•

The initial position of the connector coupling lever must be as indicated in the figures.

TABLE J2 - PROCEDURE FOR THE CORRECT

FITTING OF THE ABS CONTROL UNIT CON-

NECTOR

•

Place the connector on the opposite

side of the control unit and lower the

driving lever until the "click" that signals

the end of the stroke is heard.

TABLE J3 - PROCEDURE FOR THE CORRECT

FITTING OF THE ABS CONTROL UNIT CON-

NECTOR

•

When the connector is fully inserted,

the distance between the connector

and the ABS control unit must be 7.5

mm.

RS 660 - Tuono 660

Electrical system

ELE SYS - 101

Summary of Contents for RS 660





































































































































































































































































































































































































































Reviews:

No comments