APRILIA DORSODURO 900 2018 Manual Download Page 98

Page: 98 / 160

03_18

•

Slowly release the clutch lever (3) and at the same time accelerate by turning
the throttle (2).

The vehicle starts moving forward.

•

For the first kilometres travelled, limit the speed in order to warm up the en-
gine.

NOTE

THE VEHICLE HAS AN RPM LIMITER THAT IS PART OF THE "RIDE-BY-WIRE"
INJECTION SYSTEM.

•

Increase speed by gradually turning the throttle grip (2), without exceeding
the recommended rpm.

SELECT THE APPROPRIATE GEAR AND SPEED FOR THE CONDITIONS.

DO NOT ALLOW THE ENGINE SPEED TO DROP EXCESSIVELY.

•

Release the throttle (2), operate the clutch lever (3), lift the gear lever (4),
release the clutch (3) and accelerate.

•

Repeat the last two operations and engage a higher gear.

IF THE GENERAL WARNING LIGHT LIGHTS UP ON THE DASHBOARD, AC-
COMPANIED BY THE MESSAGE "ALLARM OIL PRESSURE" ON THE DIGITAL
DISPLAY, WHEN THE ENGINE IS RUNNING NORMALLY, IT MEANS THAT THE
ENGINE OIL PRESSURE IS LOW.

IN THIS CASE STOP THE ENGINE AND CONTACT AN Official Aprilia Dealer.

3 Use

Summary of Contents for DORSODURO 900 2018

































































































































































Search results

Summary of Contents for DORSODURO 900 2018

Reviews:

Related manuals for DORSODURO 900 2018

Brands by name

Popular brands

APRILIA DORSODURO 900 2018, Manual

Search results

Summary of Contents for DORSODURO 900 2018

Reviews:

Related manuals for DORSODURO 900 2018

Brands by name

Popular brands