Applied Motion Products ST10-S Hardware Manual Download Page 31

Page: 31 / 32

ST5/10-S Hardware manual

920-0027 Rev. A1

6/1/09

Mating Connectors and Accessories

Mating Connectors

Motor/power supply: PCD P/N ELFP06210, included with drive.

Signal Connectors: 5 way = PCD P/N ELVP05100 , 6 way = PCD ELVP06100

Regeneration Clamp:

Applied Motion Products

RC05

CONTROLLER:

S Models

NON-VOLATILE STORAGE

Configurations are saved in FLASH memory on-board the DSP.

MODE OF OPERATION

Step & Direction, CW/CCW, A/B Quadrature, Oscillator, Joystick, SCL, Hub.

STEP AND DIRECTION INPUTS

Optically Isolated, Differential, 5 Volt. Minimum pulse width = 250 ns. Maximum

pulse frequency = 2 MHz

Function: Step & Direction, CW/CCW Step, A/B Quadrature, Run/Stop & Direction,

Jog CW & CCW or CW & CCW Limits / Adjustable bandwidth digital noise rejection

filter.

ENABLE INPUT

Optically Isolated, 5-12 Volt

Function: Motor Enable, Alarm Reset or Speed Select (Oscillator Mode).

OUTPUT

Optically Isolated, 24V, 10mA MAX.

Function: Fault, Motion, Tach.

ANALOG INPUT RANGE

0 to 5VDC

ANALOG INPUT RESOLUTION

12 bits

COMMUNICATION INTERFACE

RS-232

Summary of Contents for ST10-S

































Search results

Summary of Contents for ST10-S

Reviews:

Related manuals for ST10-S

Brands by name

Popular brands

Applied Motion Products ST10-S, Hardware Manual

Search results

Summary of Contents for ST10-S

Reviews:

Related manuals for ST10-S

Brands by name

Popular brands