Applied Biosystems GeneAmp PCR System 9700 User Manual Download Page 51

Page: 51 / 132

Instrument Setup 3-23

Upgrading

Firmware from a

PCMCIA Flash

Memory Card

The following procedure describes how to upgrade the firmware using a PCMCIA
Flash Memory Card.

Note

Contact your local Applied Biosystems representative to obtain a PCMCIA

Flash Memory Card.

To upgrade using a PCMCIA Flash Memory Card:

Step

Action

Insert a PCMCIA Flash Memory Card that contains the updated firmware into the
slot at the rear of the right side of the instrument.

Note

The label and arrow on the card face forward and toward the instrument.

Press the card firmly to ensure the card is seated in the slot.

IMPORTANT

Do not remove the card or turn off the instrument until the upgrade is

completed.

From the

Diagnostics

screen, press

Upgrade

From the

Diagnostics

screen, press

PCcard

The

Checksum

screen appears while the instrument checks the inserted PCMCIA

Flash Memory Card to ensure that it contains a valid firmware upgrade.

PCMCIA Flash Memory Card

GR0877

Checking PC card checksums...

Exit

Update

Summary of Contents for GeneAmp PCR System 9700





































































































































Search results

Summary of Contents for GeneAmp PCR System 9700

Reviews:

Related manuals for GeneAmp PCR System 9700

Brands by name

Popular brands

Applied Biosystems GeneAmp PCR System 9700, User Manual

Search results

Summary of Contents for GeneAmp PCR System 9700

Reviews:

Related manuals for GeneAmp PCR System 9700

Brands by name

Popular brands