Applied Biosystems GeneAmp PCR System 9700 User Manual Download Page 35

Page: 35 / 132

Instrument Setup 3-7

Turning On the Instrument

Turning On the

Instrument

To turn on the instrument:

Step

Action

Plug the power cord into the side of the instrument and into an outlet.

Press the power switch to the

position.

The cooling fan powers up, and the Start-up screens appear.

After several seconds the

Main

menu appears. You can use any of the functions

displayed above the soft keys.

Note

The Main menu should appear within a few seconds. If any permanent

patterns of lines or bars display on the screen, contact Applied Biosystems
Technical Support.

APPLIED BIOSYSTEMS

www.appliedbiosystems.com

Applied Biosystems

GeneAmp® PCR System 9700

08:00 AM

4/25/01

25.0°C

GeneAmp® PCR System 9700

Name:tc001 User:<<pe>>

Run

User

Util

Edit

Create

Summary of Contents for GeneAmp PCR System 9700





































































































































Search results

Summary of Contents for GeneAmp PCR System 9700

Reviews:

Related manuals for GeneAmp PCR System 9700

Brands by name

Popular brands

Applied Biosystems GeneAmp PCR System 9700, User Manual

Search results

Summary of Contents for GeneAmp PCR System 9700

Reviews:

Related manuals for GeneAmp PCR System 9700

Brands by name

Popular brands