Applied Biosystems GeneAmp PCR System 9700 User Manual Download Page 18

Page: 18 / 132

1-8 Introduction and Safety

About Waste

Disposal

As the generator of potentially hazardous waste, it is your responsibility to perform the
actions listed below.

♦

Characterize (by analysis if necessary) the waste generated by the particular
applications, reagents, and substrates used in your laboratory.

♦

Ensure the health and safety of all personnel in your laboratory.

♦

Ensure that the instrument waste is stored, transferred, transported, and disposed
of according to all local, state/provincial, or national regulations.

Note

Radioactive or biohazardous materials may require special handling, and disposal

limitations may apply.

Summary of Contents for GeneAmp PCR System 9700





































































































































Search results

Summary of Contents for GeneAmp PCR System 9700

Reviews:

Related manuals for GeneAmp PCR System 9700

Brands by name

Popular brands

Applied Biosystems GeneAmp PCR System 9700, User Manual

Search results

Summary of Contents for GeneAmp PCR System 9700

Reviews:

Related manuals for GeneAmp PCR System 9700

Brands by name

Popular brands