manualshive.com logo in svg

Applied Biosystems 2720, User Manual

Share
Download
Applied Biosystems 2720 User Manual Download Page 101

93

Thermal Cycler Temperature Verification System For GeneAmp

® 

PCR Systems 2720, 9600, 9700, 9800, 

and Veriti

®

 System User Guide

Chapter 8

Calibration verification test

Configuring the

GeneAmp

®

 9800

1. Complete the procedures in 

“Setting up the 0.1-mL probe assembly” on 

page 92

.

2. Power on the GeneAmp

®

 9800.

For best results, allow the thermal cycler 15 to 30 minutes to warm up to 
ambient temperature before performing the test.

3. When the main menu opens, press 

Util 

to open the Utilities

 

screen.

4. Press 

Diag

 to open the Diagnostics screen.

5. Press 

F3

 (TmpVer) to open the Temperature Verification screen.

6. Press 

F1

 (Temp). This action opens the Calibration Verification screen and 

configures the GeneAmp

®

 9800 for the calibration verification test.

7. Continue with 

“Running the test”

 below.

Running the test

Use the digital thermometer to take temperature readings of the sample well that is 
connected to the 0.1-mL probe assembly. You take a reading at each of two setpoint 
temperatures.

Note:

If necessary, press 

F5

 (Cancel) to exit the test.

To run the calibration verification test:

1. Complete the procedures in 

“Configuring the GeneAmp

®

 9800”

 above.

Temperature Verification

Temp - Calibration Verification
TNU - Temperature Non-Uniformity

F1

F3

F4

F5

F2

Temp

Exit

TNU

Calibration Verification

Block temp = xx.x°C Cover temp = xxx°C

Place probe in well A6
Press Run

F1

F3

F4

F5

F2

Run

Cancel

Summary of Contents for 2720
























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands