manualshive.com logo in svg

Applent Instruments Anbai AT4808, User Manual, Page: 2 / 35

Share
Download
Applent Instruments Anbai AT4808 User Manual Download Page 2

 

2 

AT4808 User's Guide 

Safety Summary 

Warning 

  Dangerour

：

 

The  following  general  safety  precautions  must  be  observed  during  all  phases  of  operation,  service,  and  repair  of  this 
instrument. Failure to comply with these precautions or with specific WARNINGS elsewhere in this manual may impair 
the protection provided by the equipment. In addition it violates safety standards of design, manufacture, and intended use 
of the instrument. 
 

Disclaimer 

The  Applent  Instruments  assumes  no  liability  for  the  customer's 
failure to comply with these requirements. 

Ground   
The Instrument 

To avoid electric shock hazard, the instrument chassis and cabinet 
must be connected to a safety earth ground by the supplied power 
cable with earth blade. 

DO NOT 
Operate  In  An  Explosive 
Atmosphere 

Do  not  operate  the  instrument  in  the  presence  of  inflammable 
gasses or fumes. Operation of any electrical instrument in such an 
environment constitutes a definite safety hazard. 

  Keep away   
from live circuit 

Operating  personnel  must  not  remove  instrument  covers. 
Component replacement and internal adjustments must be made by 
qualified maintenance personnel. Do not replace components with 
the  power  cable  connected.  Under  certain  conditions,  dangerous 
voltages may exist even with the power cable removed. To avoid 
injuries,  always  disconnect  power  and  discharge  circuits  before 
touching them. 

Operations not included in the 
manual are forbidden   

The  protection  measurements  will  be  failure  while  beyond  the 
scope. 

 

Warning: TO AVOIDE INSTRUMENT DAMAGED, PLEASE DO 
NOT PUT DC VOLT OR CURRENT IN THE TESR TERMINAL 
 

 
Safety Sign:   

 

Provide double insulation or reinforced insulation protection 

 
Waste Electrical and Elcetronic Equipment (WEEE) order 2002/96/EC 

 

Do not leave in the trash can 

Summary of Contents for Anbai AT4808




































Reviews:

No comments